VRX6671z

Clarion Co., Ltd.

Owner???s manual & Installation manual Mode d???emploi et manuel d???installation Manual de instrucciones y de instalaci??n

VRX6671z

6.5??? MONITOR & FM/AM RADIO WITH

CD/MD CHANGER CONTROL

???

MONITEUR DE 6,5 POUCES ET RADIO FM/AM

AVEC COMMANDE DE CHANGEUR

DE CD/MD

???

MONITOR DE 6,5-PULGADAS Y RADIO FM/AM

CON MANDO PARA EL CAMBIADOR DE

CD/MD

4. MODE DISPLAY

The Color LCD Display and the Information Panel on the main unit show the following displays, provid- ing information about the mode and functions operated.

Display common to each mode

1. PRECAUTIONS

WARNING

For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving are prohibited by law in some countries. Also, while driving, keep the volume to a level at which external sounds can be heard.

MAIN

Contents

1.When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc (CD/

MD) or the optical parts of the player and proper playback may not be possible. If mois- ture forms on the disc (CD/MD), wipe it off with a soft cloth. If moisture forms on the op- tical parts of the player, do not use the player for about one hour. The condensation will dis- appear naturally allowing normal operation.

4.TV broadcast reception

When receiving the TV broadcasts, the strength of the signals changes since the car is moving, so in some cases it may not be possible to receive clear pictures.

???TV signals are strongly linear, so reception is affected by buildings, mountains and other obstacles.

???Such external factors such as electric train lines, a high voltage lines, and signal devices may disturb the picture or cause noise.

Clock Time display

2.Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip.

3.This unit uses a precision mechanism. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts.

???If the reception is poor, switch to a station with good reception.

TITLE LIST mode display

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/ TV technician for help.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND VRX6671z(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

INFORMATION FOR USERS:

CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFAC-

TURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

Be sure to unfold and read the next page. / Veuillez d??plier et vous r??f??rer ?? la page suivante. / Cerci??rese de desplegar y de leer la p??gina siguiente.

2. CONTROLS / COMMANDES / CONTROLES

Main unit / Unit?? principale / Unidad principal

With the Display closed / Avec l`afficheur ferm?? / Con el visualisador cerrado

3. NOMENCLATURE

Names of Buttons

Note:

??? Be sure to read this chapter referring to the front diagrams of chapter ???2. CONTROLS??? on page 5 (unfold).

JOYSTICK Operation

Note:

???Many settings/procedures have to be performed by using the JOYSTICK ??. Be sure to read this chapter in order to operate it properly.

??? Selecting an item in the menu

Select an item displayed in the menu by oper- ating the JOYSTICK ?? upward or downward.

??? Setting an option for the selected item

With the Display open / Avec l`afficheur ouvert / Con el visualisador abierto

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.

Remarque: Veuillez d??plier cette page et vous r??f??rer aux sch??mas quand vous lisez chaque chapitre.

Nota: Cuando lea los cap??tulos, despliegue esta p??gina y consulte los diagramas.

1POWER button

FUNC (Function) button

2SEARCH button

VOLUME button

3 PLAY/PAUSE button

4 Information Panel

5 PS (Preset scan)/AS (Auto store) button SCN (Scan) button

6 DCP RELEASE lever

7 WIDE button

RPT (Repeat) button

8 TV/VTR button

RDM (Random) button

9 Z-EHCR (Z-enhancer) button

0 ISR button

! OPEN button

@ DISP (Display) button MONI ON/OFF button

# PRESET buttons (1 to 6) DIRECT buttons (1 to 6)

$ MUTE button

% BAND button

?? Color LCD display

& A-M (Audio-Mode) button

* ADJ (Adjust) button

( TITLE button

) VISUAL button

?? JOYSTICK

??? Remote Control Infrared Sensor

When the setting options for an item are listed on the right of the display, you can choose the desired option by operating the JOYSTICK ?? leftward or rightward. Then, press the center of the JOYSTICK ?? to set your choice.

??? When ???push NEXT??? is displayed next to the menu item

1. Press the ENT at the center of the JOY- STICK ?? to select the item and show the setting display for this item.

2. Operate the JOYSTICK ??upward or down- ward to select the desired setting option, then press ENT at the center of the JOY- STICK ?? to set your choice.

??? Returning to the previous mode

Select the item ???MENU??? by operating the JOY- STICK ?? leftward or rightward, then press the ENT at the center of the JOYSTICK ??.

??BAND

DISC UP

TOP

25VOLUME

Switches reception band. Moves to the next disc in Switches reception band. increasing order.

Increases and decreases volume (in all modes).

??SEARCH

??PLAY/PAUSE

???MUTE

??ISR

??DISP

MONI

Turns on and off the monitor.

Moves preset channels up and down.

No function.

???PS/AS

SCN

??WIDE

RPT

???TV/VTR

RDM

Preset scan. When pressed and held for 2 seconds: Auto store.

No function.

No function.

6. DCP

The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.

We recommend taking the DCP with you when leaving the car.

Removing the DCP

1.Turn the power off.

2.Deeply push in the DCP RELEASE lever 6 to release the DCP/Operation Panel.

DCP/RALEASE lever

3. Pull the DCP toward you and remove it.

DCP/Operation Panel

Attaching the DCP

1.Hold the DCP/Operation Panel with its rear side facing the main unit and, as shown in the figure below, put the lower edge of the panel onto the corresponding edge of the main unit.

2.Lock the DCP/Operation Panel at the upper center until a click is heard.

POWER button

3.Press the power button 1 to turn on the power .

CAUTION

???The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks.

???If the Operation Panel is kept open, the DCP may drop due to vibration of the car. This results in damage to the DCP. So close the Operation Panel or remove the DCP to store into the case.

???The connector connecting the main unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc.

Note:

???If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.

???Be sure to store the LCD panel inside the main unit when parking the car outdoors for long period of time. The LCD panel will oper-

ate properly in a temperature range of 0 to

60?? C.

???Don???t allow any liquids on the set from drinks, umbrellas etc. Doing so may damage the in- ternal circuitry.

???Do not disassemble or modify the set in any way. Doing so may result in damage.

???Do not draw the LCD panel out and use it as a tray. Also, subjecting the LCD panel to shocks may result in breakage, deformation or other damage.

???Do not let cigarettes burn the display. Doing so may damage or deform the cabinet.

???If a problem should occur, have the set in- spected at your store of purchase.

???Do not insert objects or poke in the space be- tween the LCD panel and the main unit when the panel is tilted.

???Do not place anything on the display when the panel is tilted.

???The remote controller may not work if the re- mote control sensor is exposed to direct sun- light.

???In extremely cold weather, the display move- ment may slow down and the display may darken, but this is not a malfunction. The dis- play will work normally when the temperature increases.

???Small black and shiny spots inside the LCD panel are normal for LCD products.

???The LCD panel may stop temporarily when it opens or closes, when the engine stops or when it is cold.

???Cleaning the cabinet

Use a soft, dry cloth and gently wipe off the dirt.

For tough dirt, apply some neutral detergent diluted in water to a soft cloth, wipe off the dirt gently, then wipe again with a dry cloth.

Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or cause the paint to peel. Also, leaving rubber or plastic products in contact with the cabinet for long periods of time may cause stains.

???Cleaning the LCD panel

The LCD panel tends to collect dust, so wipe it off occasionally with a soft cloth. The surface is easily scratched, so do not rub it with hard ob- jects.

CAUTION

When the unit is turned on, starting and stop- ping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume.

Note:

??? Use this unit after starting the engine.

Adjusting the volume

Operate the VOLUME button 2 in the direction of the arrows w (up) or z (down) to adjust the volume;

w: Increases the volume.

z: Decreases the volume.

???The volume level indicated in the display is in a range from 0 (minimum) to 33 (maximum).

Turning on and off the power

Note:

???Be careful about using this unit for a long time with- out running the engine. If you drain the car???s bat- tery too far, you may not be able to start the en- gine and this can reduce the service life of the battery.

1.Press the POWER button 1.

2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.

3.Press and hold the POWER button 1for 1 sec- ond or longer to turn off the power for the unit.

Note:

???About the ???SYSTEM CHECK???

The confirmation of connected equipment must be performed for this unit only when the wiring con- nection is complete and power is turned on to the unit first. When the power is supplied, ???SYSTEM ???

and ???PUSH PWR??? appear alternately in the dis- play. Press the POWER button 1, the system

check starts inside the unit. When ???COMPLETE??? appears, press once again the POWER button 1.

Selecting a mode

1.Press the FUNC button 1to change the mode of operation.

2.Each time you press the FUNC button 1, the mode of operation changes in the following order:

Radio mode ??? CD changer mode ??? MD changer mode ??? TV mode ??? Radio mode...

???External equipment not connected with CeNET is not selected.

CAUTION

While driving, keep the volume at a level at which external sounds can be heard.

Switching the display

When the panel is closed:

Press the DISP button @ to select the desired dis- play.

Each time you press the DISP button @, the dis- play switches in the following order:

Notes:

???Once selected, the preferred display becomes the default display. When a function adjustment such as volume is made, the display momentarily switches to that function???s display, then returns back to the preferred display several seconds af- ter the adjustment.

???If a title has been input, it is shown in the SUB dis- play. If no title has been input, ???---------??? appears in the display. To input a title, refer to the subsection ???Entering titles??? in ???Other Functions??? section.

???Some special characters of the title, will not be displayed on the Information Panel of the DCP. In this case, those characters will only be left blank.

Showing a mode display

When the panel is open:

Press the TITLE button ( to show the Title List display. In the Title List display, the titles of items stored in the PRESET buttons #1 to 6 are listed.

???For detailed information, refer to the section ???Title list play???.

Opening and turning the display

Notes:

???Do not place any object on the open display.

???Do not drop any object on the movable part.

???Do not expose the display to shocks.

1.Press the OPEN button ! to open the Color

LCD display ??.

???If the Color LCD display ?? is left horizontally in the open position for 10 seconds or longer, it is automatically drawn in.

2.Turn the Color LCD display ?? upwards to a good view angle.

When the monitor is turned upwards, a pic-

ture appears in the display. The Information

Panel 4 display disappears.

CAUTION

Do not turn the display unless it is completely open.

When adjusting the angle of the display be careful no to let your fingers get caught by the panel or instrument panel of the vehicle.

3.To store the Color LCD display ??in the source unit, turn it to the horizontal position until a click is heard.

Turning on and off the monitor

Pressing the DISP button @ turns the monitor on and off.

???When a button is pressed or during security moni- toring, the monitor-off mode is canceled.

Mute

Each time you press the MUTE button $, mute is turned on and off.

???MUTE??? appears when mute is turned on.

Setting the Z-enhancer

This unit comes with 3 types of sound tone effect stored in memory. Select the one you prefer.

??? The factory default setting is ???Z-EHCR OFF???.

When a Z-enhancer comes on (1-3), ???Z-EHCR??? appears in the display.

??? ???Z-EHCR 1??? (Z-Enhancer 1):

Setting emphasizing bass.

??? ???Z-EHCR 2??? (Z-Enhancer 2):

Setting emphasizing treble.

??? ???Z-EHCR 3??? (Z-Enhancer 3):

Setting emphasizing bass and treble.

??? ???Z-EHCR OFF??? (Z-Enhancer off):

Neither bass nor treble are empha- sized by the Z-enhancer.

Note:

???Incapable of operation when connecting DSP (DPH7500z).

When the panel is closed:

Each time you press the Z-EHCR button 9, the tone effect changes in the following order:

???Z-EHCR 1??? ??? ???Z-EHCR 2??? ??? ???Z-EHCR 3??? ???

???Z-EHCR OFF??? ??? ???Z-EHCR 1???...

Adjusting the bass and treble

Notes:

???This function is enabled only when the panel is open.

???This function can be adjusted only when the Z- enhancer is OFF.

When the panel is open:

1.Press the A-M button & to change into the

AUDIO-MODE display.

2.Operate the JOYSTICK ?? upward or down-

ward to select ???Z-EHCR???. Press the ENT at the center of the JOYSTICK ??to change into the Z-enhancer selecting display.

3.Operate the JOYSTICK ?? upward or down- ward to select out of:

???TYPE 1??? (Z-Enhancer 1) ???TYPE 2??? (Z-En- hancer 2)???TYPE 3??? (Z-Enhancer 3) ???OFF??? (Z-Enhancer off),

and press the ENT at the center of the JOY- STICK ?? to set a desired Z-enhancer.

4.When the setting is finished, operate the JOY-

STICK ?? rightward or leftward to move the

cursor to the ???MENU???. Then press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

???To return from the AUDIO-MODE display to the STANDARD display, press the A-M button & once again.

Adjusting the Z-enhancer

Note:

???This function is enabled only when the panel is open.

1.Press the A-M button & to change into the AUDIO-MODE display.

2.Operate the JOYSTICK ?? upward or down-

ward to select ???Z-EH LVL??? level. Press the ENT at the center of the JOYSTICK ?? to change into the Z-enhancer adjusting display.

3.Operate the JOYSTICK ?? upward or down- ward to adjust the Z-enhancer level.

???When Z-Enhancer 1 is selected, you can adjust the bass in the range of ?? 2.

???When Z-Enhancer 2 is selected, you can adjust the treble in the range of ?? 2.

???When Z-Enhancer 3 is selected, you can adjust the bass and treble in the range of ?? 2.

1.Press the A-M button & to change into the AUDIO-MODE display.

2.Operate the JOYSTICK ?? upward or down-

ward to select ???BAS/TRE???. Then press the ENT at the center of the JOYSTICK ?? to change into the BASS/TREBLE adjusting dis- play.

3.Operate the JOYSTICK ?? rightward or left- ward to adjust the ???BASS??? or ???TREBLE???.

4.Operate the JOYSTICK ?? upward or down- ward to adjust a level (adjustment range: from

-6 to 6).

5.When the adjustment is finished, operate the JOYSTICK ?? rightward or leftward to move

the cursor to ???MENU???. Then press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Adjusting the balance and fader

Note:

???This function is enabled only when the panel is open.

1.Press the A-M button & to change into the

AUDIO-MODE display.

2.Operate the JOYSTICK ?? upward or down-

ward to select ???BAL/FAD???. Then press the ENT at the center of the JOYSTICK ?? to change into the BAL/FAD adjusting display.

3.Operate the JOYSTICK ?? rightward or left- ward to select ???BALANCE??? or ???FADER???.

4.Operate the JOYSTICK ?? upward or down- ward to make an adjustment.

Adjusting range of the balance: L13 to R13

Adjusting range of the fader: front 12 / rear 12

5.When the adjustment is finished, operate the JOYSTICK ?? rightward or leftward to move

the cursor to ???MENU???. Then press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

FM reception

tuner includes signal actuated stereo control, En- hanced Multi AGC, Impulse noise reduction curcuits and Multipath noise reduction circuits.

Changing the reception area

This unit is initially set to USA frequency intervals of 10kHz for AM and 200kHz for FM.When using it outside the USA, the frequency reception range can be switched to the intervals below.

??? Setting the reception area

While pressing DISP button @, each time you press and hold the number ???6??? of the PRESET buttons # for 2 seconds or longer, the recep- tion area switches from inside the USA to out- side the USA or from outside the USA to in- side the USA.

???Any station preset memories are lost when the reception area is changed.

Listening to the radio

1.Press the FUNC button 1and select the RA-

DIO mode.

2.Press the BAND button % and select the ra- dio band. Each time the button is pressed, the radio reception band changes in the fol- lowing order:

FM1 ??? FM2 ??? FM3 ??? AM ??? FM1...

3.Press the right or left side of the SEARCH but- ton 2 to tune in the desired station.

2.Press the right or left side of SEARCH button 2 to automatically seek a station.

When the right side of SEARCH button 2 is pressed, the station is sought in the direction

of higher frequencies; if the left side of

SEARCH button 2 is pressed, the station is sought in the direction of lower frequencies.

Manual tuning

There are 2 ways available: Quick tuning and step tuning.

When you are in the step tuning mode, the fre- quency changes one step at a time. In quick tun- ing mode, you can quickly tune the desired fre- quency.

1.Press the BAND button % and select the de- sired band. (FM or AM)

???If ???MANU??? is not lit in the display (or when the

panel is closed, if the indicator ???SRCH??? is lit), press and hold the BAND button % for 1 sec- ond or longer. ???MANU??? appears in the display (or when the panel is closed, the indicator ???SRCH??? goes off) and manual tuning is now available.

2.Tune into a station.

??? Quick tuning:

Press and hold the right or left side of the SEARCH button 2 for 1 second or longer to tune in a station.

??? Step tuning:

Press the right or left side of the SEARCH but- ton 2 to manually tune in a station.

Tuning

There are 3 types of tuning mode available, seek tuning, manual tuning and preset tuning.

Seek tuning

1.Press the BAND button % and select the de- sired band. (FM or AM)

???If ???MANU??? is lit in the display (or when the panel

is closed, if the indicator ???SRCH??? is not lit) press and hold the BAND button % for 1 second or longer. ???MANU??? in the display goes off (or when the panel is open the indicator ???SRCH??? lights)and seek tuning is now available.

Recalling a preset station

A total of 24 preset positions (6-FM1, 6-FM2, 6- FM3, 6-AM) exists to store individual radio sta- tions in memory. Pressing the corresponding

PRESET buttons # recalls the stored radio fre- quency automatically.

1.Press the BAND buttons % and select the desired band. (FM or AM)

2.Press the corresponding PRESET buttons # to recall the stored station.

???Press and hold one of the PRESET buttons # for 2 seconds or longer to store that station into preset memory.

Manual memory

1.Press the BAND button % and select the de- sired band. (FM or AM)

2.Select the desired station with seek tuning, manual tuning, or preset tuning.

3.Press and hold one of the PRESET buttons

# for 2 seconds or longer to store the cur- rent station into preset memory.

Auto store

Auto store is a function for storing up to 6 sta- tions that are automatically tuned in sequentially.

If 6 receivable stations cannot be received, a pre- viously stored station remains unoverwritten at the memory position.

1.Press the BAND button % and select the de- sired band. (FM or AM)

2.Press and hold the PS/AS button 5for 2 sec- onds or longer. The stations with good recep- tion are stored automatically to the preset channels.

Preset scan

Preset scan receives the stations stored in pre- set memory in order. This function is useful when searching for desired station in memory.

1.Press the PS/AS button 5.

2.When the desired station is tuned in, press the PS/AS button 5again to continue receiv- ing that station.

Note:

???Be careful not to press and hold PS/AS button 5 for 2 seconds or longer, otherwise the auto store function engages and the unit starts storing sta- tions.

Instant station recall (ISR)

Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. The ISR function even oper- ates with the unit in other modes.

??? ISR memory

1.Select the station that you wish to store in ISR memory.

2.Press and hold ISR button 0 for 2 seconds or longer.

??? Recalling a station with ISR

In any mode, press ISR button 0 to turn on the radio function and tune the selected radio sta- tion. ???ISR??? appears in the display. Press ISR but- ton 0 again to return to the previous mode.

CD changer functions

When an optional CD changer is connected through the CeNET cable, this unit controls all

CD changer functions.This unit can control a total of 2 changers (MD and/or CD).

Press the FUNC button 1 and select the CD changer mode to start play. If 2 CD changers are connected, press the FUNC button 1 to select the CD changer for play.

???If ???NO MAG??? appears in the display, insert the magazine into the CD changer. ???LOADING??? ap- pears in the display while the player loads (checks) the magazine.

???If ???NO DISC??? appears in the display, eject the magazine and insert discs into each slot. Then, reinsert the magazine back into the CD changer.

CAUTION

CD-ROM discs cannot be played in the CD changer.

Pausing play

1.Press the PLAY/PAUSE button 3 to pause play. ???PAUSE??? appears in the display.

2.To resume play, press the PLAY/PAUSE but- ton 3 again.

Displaying CD titles

This unit can display title data for CD-text CDs and user titles input with this unit.

Each time you press and hold the DISP button @for 1 second or longer, the title display changes in the following order.

When the panel is closed:

User title (disc) ??? CD-text title (disc) ??? CD-text

title (track) ??? User title (disc)...

When the panel is open:

User title (disc) ??? CD-text title (disc & track) ???

User title (disc)...

Note:

???If the CD playing is not a CD-text CD or no user title has been input, ???----------??? appears in the dis- play.

??? Scrolling a CD-text title

When a CD-text title is longer than 16 charac- ters (8 characters when the panel is closed), you can scroll the display as follows.

When the panel is closed:

1.Display the CD-text title (disc or track).

2.Press and hold the BAND button %for 1 sec- ond or longer. The titles scroll.

When the panel is open:

1.Display the CD-text title (disc & track).

2.Press and hold the TITLE button (for 1 sec- ond or longer to scroll the disc title.

3.To scroll the track title, press for 1 second or longer the TITLE button ( within 30 seconds after scrolling the disc title.

Notes:

???If the disc title is shorter than 16 characters, the track titles begin to scroll immediately.

???If the track title is shorter than 16 characters, the track titles does not scroll.

Selecting a CD

Each of the DIRECT buttons # corresponds to a disc loaded into the magazine.

??? Selecting a disc from 1 to 6

Press the corresponding DIRECT buttons (1 to

6) # to select the desired disc.

???Selecting a disc from 7 to 12 (only when a 12 disc CD changer is used.)

Press the corresponding DIRECT buttons (7 to

12) # for 1 second or more, then select the desired disc.

Selecting a track

??? Track-up

1.Press the right side of the SEARCH button 2to move ahead to the beginning of the next track.

2.Each time you press the right side of the

SEARCH button 2, the track advances ahead to the beginning of the next track.

??? Track-down

1.Press the left side of the SEARCH button 2 to move back to the beginning of the current track.

2.Press the left side of the SEARCH button 2 twice to move to the beginning of the previ- ous track.

Fast-forward/Fast-backward

??? Fast-forward

Press and hold the right side of the SEARCH button 2 for 1 second or longer.

??? Fast-backward

Press and hold the left side of the SEARCH but- ton 2 for 1 second or longer.

Top function

The top function plays from the first track (track

No. 1) of the disc.

??? When playing a disc 1 to 6

Press the DIRECT buttons # (1 to 6) with the same number as the CD playing.

???When playing a disc 7 to 12 (only when a 12 disc CD changer is used.)

Press the DIRECT buttons # (7 to 12) with the same number as the CD playing for 1 second or longer.

Scan play

The scan play locates and plays the first 10 sec- onds of each track on a disc automatically. This function continues on the disc until it is cancelled or the mode is changed.

???The scan play is useful when you want to select a desired track.

1.Press the SCN button 5 to start scan play.

2.Press the SCN button 5 again to cancel the scan play. Current track continues to play.

Disc scan play

The disc scan play locates and plays the first 10 seconds of the first track on each disc in the cur- rently selected CD changer. This function con- tinues automatically until it is cancelled or the mode is changed.

???The disc scan play is useful when you want to se- lect a desired CD.

1.Press the SCN button 5 for 1 second or longer to start disc scan play.

2.Press the SCN button 5 again to cancel disc scan play. Normal disc play continues on the current track.

Repeat play

The repeat play continuously plays the current track. This function continues automatically until it is cancelled or the mode is changed.

1.Press the RPT button 7, to make repeat play starts. ???RPT??? lights in the display.

2.To cancel repeat play, press the RPT button

7 again. ???RPT??? goes off from the display and the unit returns to normal play.

Disc repeat play

After all tracks in the current disc have been played, the disc repeat play automatically replays the current disc over from the first track.This func- tion continues automatically until it is cancelled or the mode is changed.

1.When you press the RPT button 7 for 1 sec- ond or longer, disc repeat play starts. ???D-RPT??? lights in the display.

2.To cancel disc repeat play, press the RPT button 7 again. ???D-RPT??? goes off from the display and the unit returns to normal play from the track being played.

Random play

The random play selects and plays individual tracks on the disc in no particular order. This func- tion continues automatically until it is cancelled or the mode is changed.

1.When you press the RDM button 8, random play starts. ???RDM??? lights in the display.

2.To cancel random play, press the RDM but- ton 8 again. ???RDM??? goes off from the dis- play and the unit returns to normal play.

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular or- der. This function continues automatically until it is cancelled or the mode is changed.

1.When you press the RDM button 8for 1 sec- ond or longer, disc random play starts. ???D- RDM??? lights in the display.

2.To cancel disc random play, press the RDM button 8 again. ???D-RDM??? goes off from the display and the unit returns to normal play from the track being played.

MD changer functions

When an optional MD changer is connected through the CeNET cable, this unit controls all

MD changer functions. This unit can control a total of 2 changers (MD and/or CD).

Press the FUNC button 1 and select the MD changer mode to start play. If 2 MD changers are connected, press the FUNC button 1 to se- lect the MD changer for play.

???If ???NO DISC??? appears in the display, load MDs into the MD changer.

Pausing play

1.Press the PLAY/PAUSE button 3 to pause play. ???PAUSE??? appears in the display.

2.To resume play, press the PLAY/PAUSE but- ton 3 again.

Switching disc titles and track titles

This unit can display disc titles and track titles already entered on MDs. Titles up to 128 char- acters long can be displayed by scrolling the titles.

??? Titles cannot be entered for MDs with this unit.

When the panel is closed:

1.Press the DISP button @ to show the SUB display. The disc title or track title is displayed.

2.Each time you press and hold the DISP but- ton @ for 1 second or longer, the display toggles between the disc title and the track title.

When the panel is open:

Both disc and track titles are displayed.

Scrolling titles

When a title is longer than 16 characters (or 8 characters if the panel is closed), you can scroll through it with the following operation.

When the panel is closed:

1.Display the MD title (disc or track).

2.Press the BAND button % for 1 second or longer. The display scrolls through the title.

When the panel is open:

1.Press the TITLE button ( for 1 second or longer to scroll through the disc title.

2.To scroll the track title, press for 1 second or longer the TITLE button ( within 30 seconds after scrolling the disc title.

Notes:

???When the disc title is within 16 characters, the title is scrolled immediately.

???If the track title is shorter than 16 characters, the track titles does not scroll.

Selecting an MD

Each of the DIRECT buttons # corresponds to an MD loaded into the MD changer.

Press the DIRECT buttons # (1 to 6) and select the desired MD.

Selecting a track

??? Track-up

1.Press the right side of the SEARCH button 2to move ahead to the beginning of the next track.

2.Each time you press the right side of the SEARCH button 2, the track advances ahead to the beginning of the next track.

??? Track-down

1.Press the left side of the SEARCH button 2 to move back to the beginning of the current track.

2.Press the left side of the SEARCH button 2 twice to move to the beginning of the previ- ous track.

Fast-forward/Fast-backward

??? Fast-forward

Press and hold the right side of he SEARCH but- ton 2 for 1 second or longer.

??? Fast-backward

Press and hold the left side of he SEARCH but- ton 2 for 1 second or longer.

Top function

The top function plays from the first track (track No. 1) of the disc.

Press the DIRECT buttons # (1 to 6) with the same number that the MD playing.

???If an MD is not loaded in a slot of the MD changer, pressing the DIRECT buttons # corresponding to its disc number is invalid.

Scan play

The scan play locates and plays the first 10 sec- onds of each track on a disc automatically. This function continues on the disc until it is cancelled or the mode is changed.

???The scan play is useful when you want to select a desired track.

1.When you press the SCN button 5, scan play starts.

2.Press the SCN button 5 again to cancel the play. Current track continues to play.

Disc scan play

The disc scan play locates and plays the first 10 seconds of the first track on each disc in the cur- rently selected MD changer. This function con- tinues automatically until it is cancelled or the mode is changed.

???The disc scan play is useful when you want to select a desired MD.

1.When you press the SCN button 5for 1 sec- ond or longer, disc scan play starts.

2.To cancel disc scan play, press the SCN but- ton 5 again. Normal disc play continues on the current track.

Repeat play

The repeat play continuously plays the current track. This function continues automatically until it is cancelled or the mode is changed.

1.When you press the RPT button 7, repeat play starts. ???RPT??? lights in the display.

2.To cancel repeat play, press the RPT button

7 again. ???RPT??? goes off from the display and the unit returns to normal play.

Disc repeat play

After all the tracks on the current disc have been played, the disc repeat play automatically replays the current disc over from the first track.This func- tion continues automatically until it is cancelled or the mode is changed.

1.When you press the RPT button 7 for 1 sec- ond or longer, disc repeat play starts. ???D-RPT??? lights in the display.

2.To cancel disc repeat play, press the RPT button 7 again. ???D-RPT??? goes off from the display and the unit returns to normal play from the track being played.

Random play

The random play selects and plays individual tracks on the disc in no particular order.This func- tion continues automatically until it is cancelled or the mode is changed.

1.When you press the RDM button 8, random play starts. ???RDM??? lights in the display.

2.To cancel random play, press the RDM but- ton 8 again. ???RDM??? goes off from the dis- play and the unit returns to normal play.

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular or- der. This function continues automatically until it is cancelled or the mode is changed.

1.When you press the RDM button 8for 1 sec- ond or longer, random play starts. ???D-RDM??? lights in the display.

2.To cancel random play, press the RDM but- ton 8 again. ???D-RDM??? goes off from the dis- play and the unit returns to normal play from the track being played.

TV functions

When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV requires a TV tuner.

WARNING

For your safety, the driver should not watch the TV or operate the controls while driv- ing. Please note that watching and operat- ing the TV while driving are prohibited by law in some countries.

Watching TV

Notes:

???For your safety, this unit has a safety function which turns off the picture when the car is moving, so only the audio can be heard. The picture can only be watched when the car is stopped and the park- ing break is applied.

1.Press the FUNC button 1 and select the TV mode.

2.Press the BAND button % to select the de- sired TV band (TV1 or TV2). Each time the button is pressed, the input selection toggles between TV1 and TV2.

3.Press the right or left side of the SEARCH button 2 to tune in the desired TV station.

Watching a video

The TV tuner has a VTR input terminal to which 1 external device can be connected. Connect a 12V video cassette player (VCP) or video cas- sette recorder (VCR) to the TV tuner input termi- nal.

1.Press the RDM button 8and select the VTR.

2.To return to the TV broadcast, press the RDM button 8 again.

Tuning

There are 3 types of tuning mode available, seek tuning, manual tuning and preset tuning.

Seek tuning

1.Press the BAND button % and select the de- sired TV band (TV1 or TV2).

???If ???MANU??? is lit in the display (or when the panel is closed, if the indicator ???SRCH??? is not lit),

press and hold the BAND button % for 1 sec- ond or longer. ???MANU??? in the display goes off (or when the panel is closed, the indicator ???SRCH??? lights) and seek tuning is now avail- able.

2.Press the right or left side of the SEARCH button 2 to automatically seek a station. Press the right side of the SEARCH button

2 to automatically tune up the frequency band to the next available TV station; press the left side to automatically tune down.

Manual tuning

There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the de- sired frequency.

1.Press the BAND button % and select the de- sired band. (TV1 or TV2)

???If ???MANU??? is not lit in the display (or when the

panel is closed, if the indicator ???SRCH??? is lit), press and hold the BAND button % for 1 sec- ond or longer. ???MANU??? appears in the display (or when the panel is closed, the indicator ???SRCH??? goes off) and manual tuning is now available.

2.Tune into a station.

??? Quick tuning:

Press and hold the right or left side of the

SEARCH button 2for 1 second or longer to tune in a station.

??? Step tuning:

Press the right or left side of the SEARCH but- ton 2 to manually tune in a station.

Note:

???Manual tuning is cancelled if you do not operate the unit for 7 seconds longer.

Recalling a preset station

A total of 12 TV stations can be stored (6-TV1 and 6-TV2). This allows you to select your favor- ite TV stations and store them in memory for later recall.

1.Press the BAND button % and select the de- sired TV band. (TV1 or TV2)

2.To recall a stored TV station, press the de- sired PRESET buttons # to select that sta- tion.

???Press and hold one of the PRESET buttons # for 2 seconds or longer to store the current sta- tion into the preset memory.

1.Select the desired station with seek tuning, manual tuning or preset tuning.

2.Press and hold one of the PRESET buttons

# for 2 seconds or longer to store the cur- rent station to that preset memory.

Auto store

Auto store selects 6 TV stations automatically and stores each one into a preset memory.

If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory.

1.Press the BAND button % and select the de- sired TV band. (TV1 or TV2)

???This function is enabled only when the panel is open.

???Normally use the TV diver with the ???ON??? position.

You can change the reception setting for the TV antenna connected to the TV tuner.

1.Press the ADJ button * to switch to the ad- justment selection display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???TV DIVER???.

3.Operate the JOYSTICK ?? rightward or left- ward to select ???ON??? or ???OFF??? and press the ENT at the center of the JOYSTICK ?? to set the selected reception setting.

??? ON:

2.Press and hold the AS/PS button 5for 2 sec- onds or longer. The stations with good recep- tion are automatically stored to the PRESET buttons # .

Preset scan

Preset scan allows the user to view each preset position before it automatically advances to the next preset. This function is useful for searching for desired TV station in memory.

1.Press the AS/PS button 5.

2.When the desired channel is received, press the AS/PS button 5 again.

Switching the VTR system between NTSC and PAL

???This function is enabled only when the panel is open.

Switch to the VTR mode you use.

1.Press the ADJ button * to switch to the ad- justment selection display.

2.Operate the JOYSTICK ?? upward or down- ward to move the cursor to ???VTR N/P???.

3.Operate the JOYSTICK ?? rightward or left- ward to move the cursor to select ???NTSC??? or ???PAL???.

4.Press the ENT at the center of the JOYSTICK

?? to set the selected VTR mode.

Sets reception emphasizing the visual.

??? OFF:

Sets the diver setting to OFF.

4.Press the ADJ button * return to the previ- ous mode.

??? ???BRIGHT???:

Adjust the brightness of the display.

The whole image elongates horizontally.

??? ???CINEMA???: (cinema mode)

??? ???COLOR???:

Adjusts the color saturation.

??? ???HUE???:

Adjusts the tone of color (red is emphasized or green is emphasized.)

5.Operate the JOYSTICK ?? upward or down- ward to adjust a level.

6.When the adjustment is made, operate the

JOYSTICK ?? rightward or leftward to move the cursor to ???MENU???. Then press the ENT at the center of the JOYSTICK ?? to return to the adjustment selection display.

The image at both top and bottom in a dis- play disappears.

Notes:

???When a normal 4:3 size image, not being a wide one, is viewed by displaying it fully on a wide TV display in a wide mode or a full-wide mode, a part of the peripheral image will be lacking or deformed. In deference to the intention of producer, an origi- nal image can be viewed in a normal mode.

???During superimposed display, it becomes a full- wide mode.

Rear Vision Camera

Monitoring the rear vision camera

The rear vision camera can be connected to this unit. For the power supply of the camera, mount the power box sold separately (CAA-147).

Notes:

???This function is not available when the display is stored.

Operation of External Visual

Devices (VISUAL Mode)

External visual devices such as DVD and VTR devices can be connected to the DIN 8-pin ter- minal, and the image and sound can then be played using VISUAL mode.

Notes:

???While driving, the image of the VISUAL Mode is turned OFF and only sound is played.

???Images can only be played when the vehicle is stationary with the parking brake ON.

1.With the panel open, push VISUAL button ) to switch from radio, TV, CD/MD changer mode to VISUAL mode.

2.To exit VISUAL Mode and return to the previ- ous mode, press VISUAL button ) again.

???The image format played in VISUAL mode can be set to NTSC or PAL format. The setting method is the same as for the TV. Please refer to the TV explanation.

???In VISUAL mode, the picture quality can be ad- justed. The setting method is the same as for the TV. Please refer to the TV explanation.

Always turning on the button illumination on the operation panel

Note:

???The following operation is enabled when the panel is open.

The button illumination on the operation panel when the display is turned upward, can be switched between ???ON??? and ???OFF???.

??????ON???: Button illumination on the operation panel turns on for 5 seconds;

??????OFF??? : Button illumination is always on when the power is turned on;

1.When the panel is open, press the ADJ button ?? to show the adjustment selection display.

2.Operate the JOYSTICK ?? upward or down- ward and select ???AUTO ILL??? to show ???ON??? and ???OFF??? in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select either position to be set and press the ENT at the center of the JOYSTICK ?? for setting.

4.Press the ADJ button * to return to the pre- vious mode.

???To set ???ON??? again, switch ???OFF??? to ???ON??? manually.

Entering titles

Titles up to 10 characters long can be stored in memory and displayed.The numbers of titles that can be entered for each mode are as follows.

???You cannot enter titles with the unit in Seek, Pre- set Scan, Auto store (TUNER, TV), Scan, Repeat or Random (CD changer, MD changer) mode. Can- cel each of those operations before entering titles.

1.Press the FUNC button 1to select the mode you want to enter a title (CD changer or TV).

2.Select and play a CD in the CD changer or tune in to a TV station for which you want to enter the title.

3.If you press and hold the TITLE button ( for 1 second or longer, the display switches to the title input mode display.

4.Operate the JOYSTICK ?? upward or down- ward, rightward or leftward and move the cur- sor to the character to be entered. Press the

ENT at the center of the JOYSTICK ??.

???When the cursor is at the lower/upper limit of the display, operate the JOYSTICK ?? upward or downward, the character string of the follow- ing line appears.

5.Repeat the step 4 to enter the complete title.

6.Press and hold the ENT at the center of the

JOYSTICK ?? for 2 seconds or longer to store the title into memory and cancel title input mode.

Title list play

You can display a list of titles, then select the disc or broadcast station to listen to from that list.

???You can not display a title list with the unit in Seek, Preset Scan, Auto store (Tuner or TV), Scan, Re- peat or Random (CD changer or MD changer) mode. Cancel those operation modes before to display a title list.

1.With the unit in radio, CD/MD changer, TV, press the TITLE button (. A title list is dis- played. The following functions can be car- ried out in a title list display.

???TUNER: A title of a channel stored in the presets 1 to 6 or a channel number is dis- played.

???CD/MD changer: DISC titles for discs 1 to 6 are displayed (By changing over a display page in case of 12-CD changer, disc 7 to 12 can be displayed). When there is not any disc in a changer, ???---------??? is displayed.

???TV: A title of a channel stored in the pre- sets 1 to 6 or a channel number is displayed.

2.Operate the JOYSTICK ?? upward or down- ward to select one of the items 1 to 6. Press

ENT at the center of the JOYSTICK ?? to re- produce the selected broadcast station or disc.

???In case of 12-CD changer, move the cursor to disc 6 and then operate the JOYSTICK ?? downward to change over to a list display of discs 7 to 12.

3.Press the TITLE button ( again to return to the STANDARD display.

DSP control function

If the DSP (DPH7500z), sold separately, is con- nected to this unit using the CeNET cable, all the functions of the DSP can be controlled.

???When the DSP is connected, an external ampli- fier is required.

???DSP control can all be operated only when the panel is open.

DSP functions

There are 2 modes available in DPH7500z, easy mode and professional mode. Choose one of them and adjust the sound field and the sound quality.

??? Functions common to each mode:

Such as auto loudness, subwoofer etc.

??? Easy mode:

Adjustment using the graphic equalizer function and the DSP function.

??? Professional mode:

Adjustment using the space equalizer function and the parametric equalizer function.

???When the easy mode is selected, adjustment for the professional mode cannot be made. On the contrary, when the professional mode is selected, adjustment for the easy mode cannot be made.

???For details on functions of each mode, refer to the owner???s manual supplied with the DPH7500z.

???Hereafter the graphic equalizer is referred to as a G.EQ, the space equalizer referred to as S.EQ and the parametric equalizer referred to as P.EQ.

Operations common to each mode

Output adjustment of auto loudness, subwoofer and playback band

1.Press the ADJ button * to switch to the ad- justment selection display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???SOUND??? and press the ENT at the center of the JOYSTICK ?? to change into the Sound adjustment display. In the

Sound adjustment display ???A.LD LEVEL???, ???W.OUT???, ???W.LPF???, ???HPF???, ???T.TONE??? are listed.

Operate the JOYSTICK ?? rightward or left- ward to select an item to be adjusted.

3.To make an adjustment on:

??? Auto loudness adjustment

Operate the JOYSTICK ?? upward or down- ward to adjust an auto loudness level (0 to

10).

??? Woofer out adjustment

Select woofer output out of ???STEREO???,

???MONO???, or ???OFF???.

Operate the JOYSTICK ?? upward or down- ward to select a desired item, and then press the ENT at the center of the JOYSTICK ?? to set it.

??? Woofer LPF adjustment

Select woofer LPF slope out of ???50Hz???, ???80Hz???, ???120Hz???.

Operate the JOYSTICK ?? upward or down- ward to select a desired item, and then press the ENT at the center of the JOYSTICK ?? to set it.

??? HPF adjustment

Select HPF slope out of ???50Hz???, ???80Hz???,

???120Hz???, or ???OFF???.

Operate the JOYSTICK ?? upward or down- ward to select a desired item, and then press the ENT at the center of the JOYSTICK ?? to set it.

??? Test Tone Output

Select Test Tone Output

Operate the JOYSTICK ?? upward or down- ward to select a desired item, and then press the ENT at the center of the JOYSTICK ?? to produce a test tone.

4.After adjustment (setting), operate the JOY- STICK ?? rightward or leftward to move the cursor to ???MENU??? and press the ENT at the center of the JOYSTICK ?? to return to the adjustment selection display.

5.Press the ADJ button * again to return to the STANDARD display.

Selecting the easy mode or the professional mode

??? The factory default setting is ???EASY???.

1.Press the ADJ button * to switch to the ad- justment selection display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???DSP/EQ???. ???EASY??? and ???PRO??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select a desired mode and press the

ENT at the center of the JOYSTICK ?? to set the mode thus selected.

4.After setting, press the ADJ button * again to return to the STANDARD display.

Woofer level adjustment

You can adjust an output sound level of subwoofer.

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???W-VOL??? and press the ENT at the center of the JOYSTICK ?? to show the woofer level adjusting display.

3.Operate the JOYSTICK ?? upward or down- ward to adjust the level (0 to 14).

4.After adjustment, operate the JOYSTICK ?? rightward or leftward to select ???MENU??? and press the ENT at the center of the JOYSTICK ?? return to the AUDIO-MODE display.

Easy mode/Setting the listening position

Selection of listening position

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???POSITION???. ???SELECT" and

???DETAIL??? are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select ???SELECT???, and press the ENT at the center of the JOYSTICK ?? to show Position selecting display.

4.Operate the JOYSTICK ?? upward or down- ward and press the ENT at the center of the JOYSTICK ?? to select a desired position.

5.Operate the JOYSTICK ?? rightward or left- ward to move the cursor to ???MENU???, and press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Detail adjustment of listening position

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???POSITION???. ???SELECT" and

???DETAIL??? are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select ???DETAIL???, and press the ENT at the center of the JOYSTICK ?? to show Position Detail adjusting display.

4.Operate the JOYSTICK ?? rightward or left- ward to select ???BALANCE??? or ???FADER???.

5.Operate the JOYSTICK ?? upward or down- ward to make an adjustment.

6.Operate the JOYSTICK ?? rightward or left- ward to move the cursor to ???MENU???, and press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Easy mode/G.EQ operations

Note:

???The adjustment made in easy mode is not reflected in the adjustment in professional mode. Respec- tively, the adjustment made in professional mode is not reflected in the adjustment in easy mode.

G.EQ effect ON/OFF

??? The factory default setting is ???ON???.

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???EQ ON/OFF???. ???ON??? and ???OFF??? items are displayed in the menu bar.

3.Operate the JOYSTICK ??rightward or leftward to select ???ON??? or ???OFF??? and press the ENT at the center of the JOYSTICK ?? to set it.

4.After the setting, press the A-M button & again to return to the STANDARD display.

Note:

???If the G.EQ effect is set to OFF, the adjustment made in ???G.EQ operations??? is not reflected in the music source.

Calling G.EQ BASIC Pattern/USER

Pattern

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???EQ MODE???. ???BASIC??? and ???USER??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select the item thus called, and press the ENT at the center of the JOYSTICK ?? to show BASIC pattern selecting display or USER pattern selection/memory display.

4.In the Pattern selecting display, operate the

JOYSTICK ?? rightward or leftward to select P1 to P6, and press the ENT at the center of the JOYSTICK ??to call corresponding G.EQ pattern. In this display, pressing the No. but- ton in correspondence to the PRESET button

# can also call the G.EQ pattern.

???After selecting P1 to P6 by the JOYSTICK ??, press ENT at the center of the JOYSTICK ?? for 2 seconds or longer to copy the selected pattern to the USER pattern.

???Operate the JOYSTICK ??rightward or leftward

to select ???EDIT???, and press the ENT at the cen- ter of the JOYSTICK ?? to show G.EQ adjust- ing display, in which the properties of currently selected pattern can be adjusted.

???By pressing the BAND button % in BASIC pat- tern selecting display or USER pattern selec- tion/memory display you can switch between the two patterns, BASIC and USER.

5.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU???, and press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Setting and storing G.EQ Proper- ties/Memory into USER Pattern

1.Repeat the steps 1 to 3 of the previous proce- dure (Calling G.EQ BASIC Pattern/USER Pat- tern) to show BASIC pattern selecting display or USER pattern selection/memory display.

2.Operate the JOYSTICK ?? leftward and right- ward to select ???EDIT???, and press the ENT at the center of the JOYSTICK ?? to show the

G.EQ adjusting display.

3.When some frequency to be adjusted is se- lected by operating the JOYSTICK ?? right- ward or leftward in the G.EQ adjusting display, a gain setting value at the selected frequency is displayed.

4.Operate the JOYSTICK ?? upward or down- ward to adjust the G.EQ GAIN.

???By pressing the PRESET buttons #once in the G.EQ adjusting display, the setting value for cur- rently stored USER pattern is obtained.

5.After making adjustments to a desired pattern by repeating the operations of items 3 and 4, operate the JOYSTICK ?? rightward or left- ward to move the cursor to ???RTN???, and press the ENT at the center of the JOYSTICK ?? to change over to the BASIC/USER pattern se- lection/memory display.

6.Operate the JOYSTICK ??rightward or leftward in the BASIC/USER pattern selection/memory display to select USER memory P1 to P6 to be stored, and press the ENT at the center of the JOYSTICK ?? for 2 seconds or longer to store the adjusted G.EQ pattern to the USER memory.

???By pressing the PRESET button # 1 to 6 for 2 seconds or longer in the G.EQ adjusting dis- play, the G.EQ pattern can be stored in the USER memory.

7.To set a title of the stored USER pattern, op- erate the JOYSTICK ?? rightward or leftward to select ???TITLE??? and press the ENT at the center of the JOYSTICK ??to change into the

Title Input display.

???For title inputting method, refer to the section ???Entering titles???.

8.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU??? and press the ENT at the center of the JOYSTICK ??to change into the AUDIO-MODE display.

Easy mode/DSP operations

DSP effect ON/OFF

??? The factory default setting is ???ON???.

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???DSP ON/OFF???. ???ON??? and

???OFF??? items are displayed in the menu bar.

3.Operate the JOYSTICK ??rightward and left- ward to select ???ON??? or ???OFF??? and press the

ENT at the center of the JOYSTICK ?? to set it.

Note:

???If the DSP effect is set to OFF, the adjustment made in ???DSP operations??? is not reflected in the music source.

Calling DSP BASIC Pattern/USER

Pattern

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???DSP MODE???. ???BASIC 1???, ???BA- SIC 2??? and ???USER??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select the item thus called, and press the ENT at the center of the JOYSTICK ?? to show BASIC pattern selecting display or

USER pattern selection/memory display.

4.In the pattern selecting display, operate the

JOYSTICK ?? rightward or leftward to select

P1 to P6, and press the ENT at the center of the JOYSTICK ?? to call corresponding DSP mode. In this display, pressing the No. button in correspondence to the PRESET buttons # can also call the DSP mode.

???After selecting P1 to P6 by operating the JOY- STICK ??, press the ENT at the center of the JOYSTICK ?? for 2 seconds or longer to copy the selected pattern to the USER pattern.

???Operate the JOYSTICK ?? rightward or left-

ward to select ???EDIT???, and press the ENT at the center of the JOYSTICK ?? to show DSP adjusting display, in which the properties of cur- rently selected pattern can be adjusted.

???By pressing the BAND button %in BASIC pat- tern selecting display or USER pattern selec- tion/memory display you can switch between the two patterns, BASIC and USER.

5.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU???, and press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Setting and storing DSP Properties/ Memory into USER Pattern

1.Repeat the steps 1 to 3 of the previous proce- dure (Calling DSP BASIC Pattern/USER Pat- tern) to show BASIC pattern selecting display or USER pattern selection/memory display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???EDIT???, and press the ENT at the center of the JOYSTICK ?? to show the

DSP adjusting display.

3.Select an item to be adjusted by operating the JOYSTICK ??rightward or leftward in the DSP adjusting display.

???EF??? ??? EFFECT

???DL??? ??? DELAY

???R.M??? ??? REAR MIX

???R.S??? ??? ROOM SIZE ???LV??? ??? LIVENESS

???R.T??? ??? REVERB TIME ???HI??? ??? HIGH

4.Operate the JOYSTICK ?? upward or down- ward to set each adjusting value.

???By pressing the PRESET buttons # once in the DSP adjusting display, the setting value for currently stored USER pattern is obtained.

5.After making adjustments to a desired pattern by repeating the operations of items 3 and 4, operate the JOYSTICK ?? rightward or left- ward to move the cursor to ???RTN???, and press the ENT at the center of the JOYSTICK ?? to change over to the BASIC/USER pattern se- lection/memory display.

6.Operate the JOYSTICK ?? rightward or left- ward in the BASIC/USER pattern selection/ memory display to select USER memory P1 to P6 to be stored, and press the ENT at the cen- ter of the JOYSTICK ??for 2 seconds or longer to store the adjusted DSP pattern to the USER memory.

???By pressing the PRESET buttons # 1 to 6 for 2 seconds or longer in the DSP adjusting display, the DSP pattern can be stored in the USER memory.

7.To set a title of the stored USER pattern, op- erate the JOYSTICK ?? rightward or leftward to select ???TITLE??? and press the ENT at the center of the JOYSTICK ??to change into the

Title Input display.

???For title inputting method, refer to the section ???Entering titles???.

8.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU??? and press the ENT at the center of the JOYSTICK ??to change into the AUDIO-MODE display.

Professional mode/S.EQ opera- tions

Note:

???The adjustment made in professional mode is not reflected in the adjustment in easy mode. On the contrary, the adjustment made in easy mode is not reflected in the adjustment in professional mode.

S.EQ effect ON/OFF

??? The factory default setting is ???ON???.

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???S.EQ ON/OFF???. ???ON??? and ???OFF??? items are displayed in the menu bar.

3.Operate the JOYSTICK ??rightward or leftward to select ???ON??? or ???OFF??? and press the ENT at the center of the JOYSTICK ?? to set it.

Note:

???If the S.EQ effect is set to OFF, the adjustment made in ???S.EQ operations??? is not reflected in the music source.

Calling S.EQ BASIC Pattern/USER

Pattern

1.Press the A-M button & to show the AUDIO- MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???S.EQ MODE???. ???BASIC??? and

???USER??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select the item thus called, and press the ENT at the center of the JOYSTICK ?? to show BASIC pattern selecting display or USER pattern selection/memory display.

4.In the pattern selecting display, operate the

JOYSTICK ?? rightward or leftward to select P1 to P6, and press the ENT at the center of

the JOYSTICK ??to call corresponding S.EQ pattern. In this display, pressing the No. but- ton in correspondence to the PRESET buttons

# can also call the S.EQ pattern.

???After selecting P1 to P6 by operating the JOY- STICK ?? rightward or leftward, press the ENT at the center of the JOYSTICK ?? for 2 sec- onds or longer to copy the selected pattern to the USER pattern.

???Operate the JOYSTICK ??rightward or leftward

to select ???EDIT???, and press the ENT at the cen- ter of the JOYSTICK ?? to show the S.EQ ad- justing display, in which the properties of cur- rently selected pattern can be adjusted.

???By pressing the BAND button % in BASIC pat- tern selecting display or USER pattern selec- tion/memory display you can switch between the two patterns, BASIC and USER.

5.Operate the JOYSTICK ?? rightward or leftward

to select ???MENU???, and press the ENT at the cen- ter of the JOYSTICK ?? to return to the AUDIO- MODE display.

Setting and storing S.EQ Properties/ Memory into USER Pattern

1.Repeat the steps 1 to 3 of the previous proce- dure (Calling S.EQ BASIC Pattern/USER Pat- tern) to show BASIC pattern selecting display or USER pattern selection/memory display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???S.EQ EDIT???, and press the ENT at the center of the JOYSTICK ??to show the S.EQ adjusting display.

3.Select an item to be adjusted by operating the JOYSTICK ?? rightward or leftward in the

S.EQ adjusting display.

???DIFF??? ??? DIFFUSE ???C.WD??? ??? CAR WIDTH

???C.LG??? ??? CAR LENGTH

4.Operate the JOYSTICK ?? upward or down- ward to set each adjusting value.

???By pressing the PRESET buttons #once in the S.EQ adjusting display, the setting value for cur- rently stored USER pattern is obtained.

5.After making adjustments to a desired pattern by repeating the steps 3 and 4, operate the JOYSTICK ??rightward or leftward to move the cursor to ???RTN???, and press the ENT at the cen- ter of the JOYSTICK ?? to change over to the BASIC/USER pattern selection/memory display.

6.Operate the JOYSTICK ??rightward or leftward in the BASIC/USER pattern selection/memory display to select USER memory P1 to P6 to be stored, and press the ENT at the center of the

JOYSTICK ?? for 2 seconds or longer to store the adjusted S.EQ pattern to the USER memory.

???By pressing the PRESET buttons # 1 to 6 for 2 seconds or longer in the S.EQ adjusting dis- play, the S.EQ pattern can be stored in the USER memory.

7.To set a title of the stored USER pattern, op- erate the JOYSTICK ?? rightward or leftward to select ???TITLE??? and press the ENT at the center of the JOYSTICK ??to change into the

Title Input display.

???For title inputting method, refer to the section ???Entering titles???.

8.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU??? and press the ENT at the center of the JOYSTICK ??to change into the AUDIO-MODE display.

Professional mode/P.EQ opera- tions

P.EQ effect ON/OFF

??? The factory default setting is ???ON???.

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???P.EQ ON/OFF???, ???ON??? and

???OFF??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select ???ON??? or ???OFF??? and press the ENT at the center of the JOYSTICK ?? to set it.

Note:

???If the P.EQ effect is set to OFF, the adjustment made in ???P.EQ operations??? is not reflected in the music source.

Calling P.EQ BASIC Pattern/USER

Pattern

1.Press the A-M button & to show the AUDIO-

MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???P.EQ MODE???. ???BASIC??? and

???USER??? items are displayed in the menu bar.

3.Operate the JOYSTICK ?? rightward or left- ward to select the item thus called, and press the ENT at the center of the JOYSTICK ?? to show BASIC pattern selecting display or USER pattern selection/memory display.

4.In the pattern selecting display, operate the JOYSTICK ?? rightward or leftward to select

P1 to P6, and press the ENT at the center of the JOYSTICK ?? to call corresponding P.EQ pattern. In this display, pressing the No. but- ton in correspondence to the PRESET buttons

# can also call the P.EQ pattern.

???After selecting P1 to P6 by operating the JOY- STICK ??, press the ENT at the center of the JOYSTICK ?? for 2 seconds or longer to copy the selected pattern to the USER pattern.

???Operate the JOYSTICK ?? rightward or left-

ward to select ???EDIT???, and press the ENT at the center of the JOYSTICK ?? to show P.EQ adjusting display, in which the properties of currently selected pattern can be adjusted.

???By pressing the BAND button %in BASIC pat- tern selecting display or USER pattern selec- tion/memory display you can switch between the two patterns, BASIC and USER.

5.Operate the JOYSTICK ?? rightward or left- ward to select ???MENU???, and press the ENT at the center of the JOYSTICK ?? to return to the AUDIO-MODE display.

Setting and storing P.EQ Properties/ Memory into USER Pattern

1.In the Basic adjustment display or in the User setting display, press the A-M button & to show the AUDIO-MODE display.

2.Operate the JOYSTICK ?? upward or down- ward to select ???EDIT???, and press the ENT at the center of the JOYSTICK ?? to show the

P.EQ adjusting display.

3.Select an item to be adjusted by operating the JOYSTICK ??rightward or leftward in the P.EQ adjusting display.

4.Operate the JOYSTICK ?? upward or down- ward to set each adjusting value.

???By pressing the PRESET buttons # once in the P.EQ adjusting display, the setting value for currently stored USER pattern is obtained.

5.After making adjustments to a desired pat- tern by repeating the operations of items 3 and 4, operate the JOYSTICK ?? rightward or leftward to move the cursor to ???RTN???, and press the ENT at the center of the JOYSTICK ?? to change over to the BASIC/USER pat- tern selection/memory display.

6.Operate the JOYSTICK ?? rightward or left- ward in the BASIC/USER pattern selection/ memory display to select USER memory P1 to P6 to be stored, and press the ENT at the center of the JOYSTICK ?? for 2 seconds or longer to store the adjusted P.EQ pattern to the USER memory.

FM Tuner

Frequency Range:

87.9 MHz to 107.9 MHz

Usable Sensitivity:

11 dBf

50dB Quieting Sensitivity:

17 dBf

Alternate Channel Selecitivity:

75 dB

Stereo Separation(1 kHz):

35 dB

Frequency Response(+/-3 dB):

30 Hz to 15 kHz

AM Tuner

Frequency Range:

530 kHz to 1710 kHz

Usable Sensitivity:

25 ??? V

Audio Amplifier

Rated power output:

17 W ??? 4 (20 Hz to 20 kHz, 1%, 4 ??? )

Maximum power output: 40 W ??? 4 (EIAJ)

Speaker impedance: 4 ??? ( 4 to 8 ??? )

Drive method: TFT (thin-film transistor) active matrix driving

Pixels:

280,800 (1200 ??? 234)

General

Power source voltage:

14.4 V DC (10.8 to 15.6 V allowable)

Ground:

Negative

Current consumption:

4.0 A (1 W)

Auto Antenna Rated Current:

500 mA less

Dimensions of the Main Unit:

178 (W) ??? 50 (H) ??? 157 (D)mm

7(W) ??? 1-15/16(H) ??? 6-3/16(D)inches Weight of the Main Unit:

1.7 kg

Dimensions of the Remote Control Unit:

44 (W) ??? 110 (H) ??? 27 (D)mm

1-3/4(W) ??? 4-5/16(H) ??? 1-1/16(D)inches Weight of the Remote Control Unit:

30 g (including battery)

Input

RGB input:

Video: 0.7 +/- 0.2 Vp-p (input impedance 75

??? )

Synchronize: 0.3 V (+0.9 / -0.1) Vp-p (input

impedance: 75 ??? )

Video input:

1.0 +/- 0.2 Vp-p (input impedance 75 ??? )

Video input: Mini DIN 8P

LCD Monitor

Screen Size:

6.5-inch wide type (142 mm Width ??? 78 mm

Height)

Display method: Transmission type TN liquid crystal display

Notes:

???Specifications comply with EIAJ Standards.

???Specifications and design are subject to change without notice for further immprovement.