Cisco_Systems_TV_Cables

A P P E N D I X D

Slot Property Information???FC_MR-4, FMEC,

Multirate, Optical, and Transponder Cards

This appendix provides information on the cards supported in CTM. This appendix contains the following sections:

???D.1 FC_MR-4 Card, page D-1

???D.2 FMEC Cards, page D-7

???D.3 Multirate Cards, page D-17

???D.4 Optical Cards, page D-66

???D.5 Transponder Cards, page D-213

Note In the CTM GUI, read-only fields have a gray background.

Caution Refer to the appropriate hardware documentation before attempting to set thresholds on ONS 1580x boards. See 1.7 Related Documentation, page 1-45.

D.1 FC_MR-4 Card

This section describes the FC_MR-4 card supported within CTM.

D.1.1 Slot Properties???FC_MR-4

The Slot Properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH card slot that is selected in the NE Explorer tree. Use this property sheet to change the card properties.

The Fiber Channel 4-port (FC_MR-4) card is a 1.0625- or 2.125-Gbps Fiber Channel/Fiber Connectivity (FICON) card that integrates non-SONET or non-SDH framed protocols into a SONET or SDH time-division multiplexing (TDM) platform through virtually concatenated payloads.

The FC_MR-4 card uses pluggable Gigabit Interface Converters (GBICs) to transport non-SONET/SDH-framed, block-coded protocols over SONET/SDH in virtually concatenated or contiguously concatenated payloads. The FC_MR-4 can transport fiber channel over SONET/SDH using fiber-channel client interfaces and allows transport of one of the following at a time:

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FC_MR-4 Card

???Two contiguously concatenated (CCAT) STS-24c/VC4-8c circuits

???One STS-48c/VC4-16c CCAT

???Two virtually concatenated (VCAT) circuits (STC3c-8V/VC4-8v) compliant with ITU-T G.7041 GFP-T and Telcordia GR-253-CORE

???One STS-24c/VC4-8c CCAT and one STS-24c/VC4-8c VCAT

For the FC_MR module, the Slot Properties pane displays the following tabs: Module View, Identification, Card, Port, Alarm Behavior, RMON Thresholds, J1 Path Trace, GBIC Inventory, and Info.

D.1.1.1 Module View Tab

The Module View tab displays a graphic of the FC_MR that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

D.1.1.2 Identification Tab

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FC_MR-4 Card

D.1.1.4 Port Tab

The Port tab allows you to view and update FC_MR port information. The tab contains the following subtabs:

???D.1.1.4.1 General Subtab, page D-4

???D.1.1.4.2 Distance Extension Subtab, page D-4

???D.1.1.4.3 Enhanced FC/FICON Subtab, page D-5

D.1.1.4.1 General Subtab

D.1.1.4.2 Distance Extension Subtab

The Distance Extension subtab allows you to enable the buffer-to-buffer extension between the client and the FC_MR-4 card in order to increase the dense wavelength division multiplexing (DWDM) distance without affecting the throughput.

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FC_MR-4 Card

Table D-4 Field Descriptions for the Distance Extension Subtab

Field

Port No.

Enable Distance Extension

Auto Detect Credits

Credits Available

Autoadjust GFP Buffer

Threshold

GFP Buffers Available

Description

Displays the port number.

Check to enable end-to-end distances of up to 1600 km for 1 GFC and up to 800 km for 2 GFC. When enabled, all the fields for the port are enabled.

Check to enable automatic detection of buffer credits for flow control.

Displays the number of credits available. You can set the credits available only if the Auto Detect Credits field is disabled on the port. Values should be in multiples of 2. The minimum value is 2 and the maximum value is 256.

Check to automatically adjust the threshold of the GFP buffer.

Displays the number of GFP buffers. You can set the GFP buffers as available only if the Autoadjust GFP Buffer Threshold field is disabled. Values should be in multiples of 16. The minimum value is 16 and the maximum value is 1200.

D.1.1.4.3 Enhanced FC/FICON Subtab

The Enhanced FC/FICON ISL subtab allows you to enable FPGA to drop duplicate frames.

Table D-5 Field Descriptions for the Enhanced FC/FICON Subtab

D.1.1.5 Alarm Behavior Tab

D.1.1.6 RMON Thresholds Tab

The RMON Thresholds tab allows you to create, view, and delete FC_MR-4 thresholds.

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

D.1.1.9 Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.2 FMEC Cards

This section describes the following FMEC cards supported within CTM:

???D.2.1 Slot Properties???FMEC-DS-1/E1, page D-8

???D.2.2 Slot Properties???FMEC-DS-3/E3, page D-8

???D.2.3 Slot Properties???FMEC-E1, page D-9

???D.2.4 Slot Properties???FMEC-E1-120NP, page D-11

???D.2.5 Slot Properties???FMEC-STM1E 1:1, page D-12

???D.2.6 Slot Properties???MIC-A/P, page D-15

???D.2.7 Slot Properties???MIC-C/T/P, page D-16

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

D.2.1 Slot Properties???FMEC-DS-1/E1

The Slot Properties pane displays information about the Cisco ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The ONS 15454 SDH FMEC-DS-1/E1 card provides front-mount electrical connection for 14 ITU-compliant, G.703 E-1 ports. With the FMEC-DS-1/E1 card, each E1-N-14 port operates at 2.048 Mbps over a 120-ohm, balanced cable through two 37-pin DB connectors.

For the FMEC DS-1/E1 module, the Slot Properties pane displays the following tabs: Module View and Identification.

D.2.1.1 Module View Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.2.2 Slot Properties???FMEC-DS-3/E3

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

The ONS 15454 SDH FMEC-DS-3/E3 card provides front-mount electrical connection for 14 ITU-compliant, G.703 E-1 ports. With the FMEC-DS-3/E3 card, each E1-N-14 port operates at 2.048 Mbps over a 120-ohm, balanced cable through two 37-pin DB connectors.

For the FMEC DS-3/E3 module, the Slot Properties pane displays the following tabs: Module View and Identification.

D.2.2.1 Module View Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.2.3 Slot Properties???FMEC-E1

Cisco Transport Manager Release 7.2 User Guide

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

The ONS 15454 SDH FMEC-E1 card provides front-mount electrical connection for fourteen ITU-compliant, G.703 E-1 ports. With the FMEC-E1 card, each E1-N-14 port operates at 2.048 Mbps over a 75-ohm unbalanced coaxial 1.0/2.3 miniature coaxial connector.

For the FMEC-E1 module, the Slot Properties pane displays the following tabs: Module View,

Identification, and Info.

D.2.3.1 Module View Tab

D.2.3.3 Info Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.2.4 Slot Properties???FMEC-E1-120NP

The ONS 15454 SDH FMEC-E1-120NP (Unprotected) card provides front-mount electrical connection for 42 ITU-compliant, G.703 E-1 ports. With the FMEC E1-120NP card, each E1-42 port operates at 2.048 Mbps over a 120-ohm, balanced interface. Twenty-one interfaces are led through one common Molex 96-pin LFH connector.

The ONS 15454 SDH FMEC E1-120PROA (1:3 Protect A) card provides front-mount electrical connection for 42 ITU-compliant, G.703 E-1 ports. With the FMEC E1-120PROA card, each E1-42 port operates at 2.048 Mbps over a 120-ohm, balanced interface. Twenty-one interfaces are led through one common Molex 96-pin LFH connector.

The ONS 15454 SDH FMEC E1-120PROB (1:3 Protect B) card provides front-mount electrical connection for 42 ITU-compliant, G.703 E-1 ports. With the FMEC E1-120PROB card, each E1-42 port operates at 2.048 Mbps over a 120-ohm, balanced interface. Twenty-one interfaces are led through one common Molex 96-pin LFH connector.

For the FMEC-E1-120NP module, the Slot Properties pane displays the following tabs: Module View, Identification, and Info.

D.2.4.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

D.2.4.3 Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.2.5 Slot Properties???FMEC-STM1E 1:1

The ONS 15454 SDH FMEC-STM1E 1:1 card provides front-mount electrical connection for 2 x 12 ITU-compliant, G.703 STM1E ports. With the FMEC-STM1E 1:1 card, each interface of an STM1E-12 card operates at 155.52 Mbps for STM-1 over a 75-ohm unbalanced coaxial 1.0/2.3 miniature coaxial connector. The FMEC STM1E 1:1 card is required if you want to use the STM1E-12 card in 1:1 protection mode or for connection to two unprotected STM1E-12 cards.

For the FMEC-STM1E card, the Slot Properties pane displays the following tabs: Module View, Identification, and Info.

D.2.5.1 Module View Tab

The Module View tab displays a graphic of the FMEC-STM1E 1:1 card that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

D.2.6 Slot Properties???MIC-A/P

The MIC-A/P card provides connection for the BATTERY B input, one of the two possible redundant power supply inputs. It also provides connection for eight alarm outputs (coming from the TCC2 card), sixteen alarm inputs, and four configurable alarm inputs/outputs. Its position is in slot 23 in the center of the ONS 15454 SDH subrack EFCA area.

For the MIC-A/P module, the Slot Properties pane displays the following tabs: Module View and Identification.

D.2.6.1 Module View Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

FMEC Cards

D.2.7 Slot Properties???MIC-C/T/P

The MIC-C/T/P card provides connection for the BATTERY A input, one of the two possible redundant power supply inputs. It also provides connection for system management serial port, system management LAN port, modem port (for future use), and system timing inputs and outputs.

For the MIC-C/T/P module, the Slot Properties pane displays the following tabs: Module View and Identification.

D.2.7.1 Module View Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3 Multirate Cards

This section describes the following multirate cards supported within CTM:

???D.3.1 Slot Properties???ASAP_4, page D-17

???D.3.2 Slot Properties???MRC-12, page D-38

D.3.1 Slot Properties???ASAP_4

The Slot Properties pane displays information about the Cisco ONS 15600 SONET slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The ONS 15600 SONET Any Service Any Port (ASAP_4) card provides up to 16 optical network interface ports, depending on the configuration. When configured for OC-192 XFP, the card provides a maximum of four OC-192 optical network interface ports. When the ASAP_4 card is configured with a combination of OC-192 XFP and lower-rate plugins such as OC-48, OC-12, or OC-3, the number of optical network interfaces is factored by four for each OC-192. For example, if the ASAP_4 card is configured with one OC-192, the card provides a maximum of 13 optical network interfaces (one for OC-192 and 12 for lower-rate plugins). If the ASAP_4 card is configured with two OC-192s, the card provides a maximum of 10 optical network interfaces (two for OC-192 and 8 for lower-rate plugins). The card can be installed in any I/O module card slot. The card provides 16 optical interfaces on the front panel. When configured for Ethernet, an ASAP port forwards Ethernet frames by encapsulating them in Cisco HDLC or GFP and transports them over SONET to the far-end GE port, where the unencapsulation is performed.

Introduced in the CTM R7.2 release, the new OC-192 XFP feature adds the capability to the existing ONS 15600 ASAP card to support 10 GB Small Form Factor Pluggable (XFP) optics. This functionality augments the ASAP card with an OC-192 line rate and allows the ASAP card to provide a range of optical service rates that scale from OC-3 to OC-192.

Note The OC-192 XFP cannot be modified once it is configured.

The Slot Properties pane for the ASAP_4 card displays the following tabs: Module View, Card Identification, Pluggable Provisioning, Line, STS, Loopback, Protection, Alarm Behavior, J1 Path Trace, Info, Ether Line, Ether Loopback, Ether Alarm Behavior, POS Alarm Behavior, POS Line, and Transceiver.

D.3.1.1 Module View Tab

D.3.1.2 Card Identification Tab

The Card Identification tab allows you to view and update identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.1.4.8 Alarm Thresh Subtab

D.3.1.5 STS Tab

The STS tab allows you to view and update ASAP_4 STS information. The STS tab contains the following subtabs:

???D.3.1.5.1 STS Config Subtab, page D-28

???D.3.1.5.2 Path Thresh 15 Min Subtab, page D-28

???D.3.1.5.3 Path Thresh 1 Day Subtab, page D-29

???D.3.1.5.4 Customer Info Subtab, page D-30

D.3.1.5.1 STS Config Subtab

D.3.1.5.2 Path Thresh 15 Min Subtab

The Path Thresh 15 Min subtab allows you to view and change the 15-minute path thresholds of the ASAP_4 card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

Table D-33 Field Descriptions for the Path Thresh 1 Day Subtab (continued)

D.3.1.5.4 Customer Info Subtab

The Customer Info subtab allows you to view the customer information.

Table D-34 Field Descriptions for the Customer Info Subtab

Field

STS No.

Customer ID

Service ID

Description

The STS number

The user-defined customer ID number

The user-defined service ID number

D.3.1.6 Loopback Tab

The Loopback tab allows you to view and update loopback information.

Table D-35 Field Descriptions for the Loopback Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.1.13 Alarm Behavior Tab

The Alarm Behavior tab contains the following subtabs:

???D.3.1.13.1 Ether Alarm Behavior Subtab, page D-36

???D.3.1.13.2 POS Alarm Behavior Subtab, page D-36

D.3.1.13.1 Ether Alarm Behavior Subtab

D.3.1.13.2 POS Alarm Behavior Subtab

D.3.1.14 POS Line Tab

The POS Line tab allows you to view and update alarm profile information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.3.2 Slot Properties???MRC-12

Note

The Slot Properties pane displays information about the Cisco ONS 15454 SONET and ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The MRC-12 multirate card (MRC) provides up to 12 OC-3/STM-1 ports, 12 OC-12/STM-4 ports, or 4 OC-48/STM-16 ports using Small Form-factor Pluggables (SFPs), in any combination of line rates. All ports are Telcordia GR-253 compliant. The SFP optics can use SR, IR, LR, coarse wavelength division multiplexing (CWDM), and DWDM SFPs to support unrepeated spans.

The ports operate at up to 2488.32 Mbps over a single-mode fiber. The MRC-12 card has 12 physical connector adapters with 2 fibers per connector adapter (Tx and Rx). The card supports VT payloads, STS-1 payloads, and concatenated payloads at STS-3c, STS-6c, STS-9c, STS-12c, STS-18c, STS-24c, STS-36c, or STS-48c signal levels. It is fully interoperable with the ONS 15454 G-Series Ethernet cards.

The card supports 1+1 unidirectional and bidirectional facility protection. It also supports 1+1 protection in 4-fiber BLSR applications for the ONS 15454 SONET and in 4-fiber MS-SPRing applications for the ONS 15454 SDH, where both span switching and ring switching might occur. You can provision this card as part of a BLSR, UPSR, or 1+1 linear configuration for the ONS 15454 SONET or an MS-SPRing, SNCP, or linear configuration for the ONS 15454 SDH.

Longer distances are possible in an amplified system using dispersion compensation.

MRC-12 cards can only protect another MRC-12 card if the card is in the same speed slot (drop or trunk slot) and if both ports have matching line rates. For example, port 1 of the MRC-12 card 1 will protect port 1 of the MRC-12 card 2 only if both ports are provisioned with the same rate (for example, OC12/STM-4). If the ports are provisioned with different rates, you cannot set a 1+1 protection.

You can install MRC-12 cards in Slots 1 through 6 and 12 through 17 with an XCVT, XC10G, XC-VXL-2.5G, XC-VXL-10G, or XC-VXC-10G card.

Note The MRC-12 card supports an errorless software-initiated cross-connect card switch when used in a shelf equipped with XC-VXL-2.5G, XC-VXL-10G, or XC-VXC-10G cards.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

The maximum bandwidth of the MRC-12 card is determined by the cross-connect card, as shown in the following table.

1.Drop slots are low-speed slots

2.Trunk slots are high-speed slots

The twelve ports of the MRC-12 card are divided into four groups, with each group having a master port as shown in the following table.

Following are the general port rate configuration rules:

???The maximum bandwidth for each port is OC-48.

???Port 1 can occupy all possible backplane bandwidth but cannot exceed OC-48.

???Each port group can have a maximum of 25% backplane bandwidth, except for group 1.

???Only a master port can occupy all possible bandwidth assigned to the group.

Based on the cross-connect card and slot limitations shown in Table D-47, the following rules apply for various synchronous transport signal (STS) available bandwidths:

???STS-12

???Port 1 is the only port that is usable as an OC-12/STM-4. If port 1 is used as an OC-12/STM-4, all other ports are disabled.

???Ports 1, 4, 7, and 10 are the only ports usable as OC-3/STM-1. If any of these ports is used as an OC-3/STM-1, Ports 2, 3, 5, 6, 8, 9, 11, and 12 are disabled.

???STS-48

???Port 1 is the only port usable as an OC-48/STM-16. If port 1 is used as an OC-48/STM-16, all other ports are disabled.

???Ports 1, 4, 7, and 10 are the only ports usable as OC-12/STM-4.

???If port 4 is used as an OC-12/STM-4, Ports 2 and 3 are disabled.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

???If port 7 is used as an OC-12/STM-4, Ports 5, 6, and 8 are disabled.

???If port 10 is used as an OC-12/STM-4, Ports 9, 11, and 12 are disabled.

???Any port can be used as an OC-3/STM-1 as long as all of the above rules are followed.

???STS-192

???Ports 1, 4, 7, and 10 are the only ports usable as OC-48/STM-16.

???If port 4 is used as an OC-48/STM-16, Ports 2 and 3 are disabled.

???If port 7 is used as an OC-48/STM-16, Ports 5, 6, and 8 are disabled.

???If port 10 is used as an OC-48/STM-16, Ports 9, 11, and 12 are disabled.

???If port 4 is used as an OC-12/STM-4, Ports 2 and 3 can be used as an OC-12/STM-4 or OC-3/STM-1.

???If port 7 is used as an OC-12/STM-4, Ports 5, 6, and 8 can be used as an OC-12/STM-4 or OC-3/STM-1.

???If Port 10 is as used as an OC-12/STM-4, Ports 9, 11, and 12 can be used as an OC-12/STM-4 or OC-3/STM-1.

???If port 4 is used as an OC-3/STM-1, Ports 2 and 3 can be used as an OC-12/STM-4 or OC-3/STM-1.

???If port 7 is used as an OC-3/STM-1, Ports 5, 6, and 8 can be used as an OC-12/STM-4 or OC-3/STM-1.

???If port 10 is used as an OC-3/STM-1, Ports 9, 11, and 12 can be used as an OC-12/STM-4 or OC-3/STM-1.

???Any port can be used as an OC-12/STM-4 or OC-3/STM-1, as long as all of the above rules are followed.

For the MRC-12 card, the Slot Properties pane displays the following tabs: Module View, Identification, Pluggable Provisioning, Line, STS, VC-4 (available only on the ONS 15454 SDH), Loopback, Protection, Alarm Behavior, Transceiver, Auto Laser Shutdown, Section Trace, J1 Path Trace, and Info. The tabs shown depend on the NE configuration.

D.3.2.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

D.3.2.2 Identification Tab

The Identification tab allows you to view and update MRC-12 card identification information.

Table D-49 Field Descriptions for the Identi???cation Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.2.3.1 Provision Pluggable Dialog Box

Click the Create button to launch the Provision Pluggable dialog box. The Provision Pluggable dialog box allows you to provision pluggable entities; for example, the PPM and PIM, and to create the ports inside these entities. See C.1.7.5.1 Provision Pluggable Dialog Box, page C-37 for more information.

D.3.2.3.2 Create Port Dialog Box

Use the Create Port dialog box to configure the port rate for a particular pluggable port module (PPM). In the Port Rate field, use the drop-down list to select the new port rate and click OK.

D.3.2.4 Line Tab (ONS 15454 SONET)

The Line tab allows you to view and update optical line performance monitoring information. The Line tab contains the following subtabs:

???D.3.2.4.1 Line Config Subtab, page D-43

???D.3.2.4.2 Line Thresh 15 Min Subtab, page D-46

???D.3.2.4.3 Line Thresh 1 Day Subtab, page D-47

???D.3.2.4.4 Physical Thresh 15 Min Subtab, page D-48

???D.3.2.4.5 Physical Thresh 1 Day Subtab, page D-48

???D.3.2.4.6 Section Thresh 15 Min Subtab, page D-49

???D.3.2.4.7 Section Thresh 1 Day Subtab, page D-49

???D.3.2.4.8 Alarm Thresholds Subtab, page D-50

D.3.2.4.1 Line Config Subtab

The Line Config subtab allows you to view and change the line settings of the MRC-12 card.

Table D-51 Field Descriptions for the Line Con???g Subtab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.2.4.8 Alarm Thresholds Subtab

The Alarm Thresholds subtab allows you to select the thresholds for the alarms.

Table D-58 Field Descriptions for the Alarm Thresholds Subtab

Field

Port No.

LBC-HIGH

LBC-LOW

OPT-HIGH

OPT-LOW

OPR-HIGH

OPR-LOW

Set OPR

Description

Port number.

Laser bias current maximum.

Laser bias current minimum.

Optical power transmitted maximum.

Optical power transmitted minimum.

Optical power received maximum.

Optical power received minimum.

Setting the optical power received (OPR) establishes the received power level as 100 percent. If the receiver power decreases, then the OPR percentage decreases to reflect the loss in receiver power. For example, if the receiver power decreases 3 dBm, the OPR decreases 50 percent.

D.3.2.5 Line Tab (ONS 15454 SDH)

The Line tab allows you to view and update optical line performance monitoring information. The Line tab contains the following subtabs:

???D.3.2.5.1 Line Config Subtab, page D-50

???D.3.2.5.2 MS Thresh 15 Min Subtab, page D-53

???D.3.2.5.3 MS Thresh 1 Day Subtab, page D-54

???D.3.2.5.4 Physical Thresh 15 Min Subtab, page D-55

???D.3.2.5.5 Physical Thresh 1 Day Subtab, page D-55

???D.3.2.5.6 RS Thresh 15 Min, page D-56

???D.3.2.5.7 RS Thresh 1 Day Subtab, page D-56

???D.3.2.5.8 Alarm Thresholds Subtab, page D-57

D.3.2.5.1 Line Config Subtab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

???SR (short reach, up to 2km distance)

???SR 1 (up to 2km distance)

???IR 1 (intermediate reach, up to 15km distance)

???IR 2 (up to 40kmm distance)

???LR 1 (long reach, up to 40km distance)

???LR 2 (up to 80km distance)

???LR 3 (up to 80km distance)

???I1

???S1

???S2

???L1

???L2

???L3

???SX (up to 550m or 270m distance based on 50um/62.5um diameter fiber)

???LX (up to 10km or 550m distance based on 50um/62.5um diameter fiber)

???CX

???T

???DX (up to 40km distance)

???HX (up to 40km distance)

???ZX (up to 80km distance)

???VX (up to 100km distance)

D.3.2.5.2 MS Thresh 15 Min Subtab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.2.5.8 Alarm Thresholds Subtab

D.3.2.6 STS Tab (ONS 15454 SONET)

The STS tab allows you to view and update MRC-12 STS information. The STS tab contains the following subtabs:

???D.3.2.6.1 STS Config Subtab, page D-57

???D.3.2.6.2 Path Thresh 15 Min Subtab, page D-58

???D.3.2.6.3 Path Thresh 1 Day Subtab, page D-58

???D.3.2.6.4 Customer Info Subtab, page D-59

D.3.2.6.1 STS Config Subtab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.2.6.4 Customer Info Subtab

The Customer Info subtab allows you to view the customer information.

Table D-70 Field Descriptions for the Customer Info Subtab

Field

STS No.

Customer ID

Service ID

Description

The STS number.

The user-defined customer ID number.

The user-defined service ID number.

D.3.2.7 VC-4 Tab (ONS 15454 SDH)

The VC-4 tab allows you to view and update MRC-12 VC-4 information. The VC-4 tab contains the following subtabs:

???D.3.2.7.1 VC-4 Config Subtab, page D-60

???D.3.2.7.2 SDH Path Thresh 15 Min Subtab, page D-60

???D.3.2.7.3 SDH Path Thresh 1 Day Subtab, page D-61

???D.3.2.7.4 Customer Info Subtab, page D-62

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Multirate Cards

D.3.2.7.4 Customer Info Subtab

The Customer Info subtab allows you to view the customer information.

Table D-74 Field Descriptions for the Customer Info Subtab

Field

VC No.

Customer ID

Service ID

Description

The VC number.

The user-defined customer ID number.

The user-defined service ID number.

D.3.2.8 Loopback Tab

The Loopback tab allows you to view and update loopback information.

Table D-75 Field Descriptions for the Loopback Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4 Optical Cards

This section describes the following optical cards supported within CTM:

???D.4.1 Slot Properties???OC12 IR/STM4 SH 1310, page D-66

???D.4.2 Slot Properties???OC12-4 IR/STM4 SH 1310, page D-75

???D.4.3 Slot Properties???OC192 LR/STM64 LH 1550, page D-85

???D.4.4 Slot Properties???OC192/STM64 XFR-Based, page D-93

???D.4.5 Slot Properties???OC3 IR 4 1310, page D-113

???D.4.6 Slot Properties???OC3 IR/STM1 SH 1310-8, page D-121

???D.4.7 Slot Properties???OC48, page D-129

???D.4.8 Slot Properties???OC48 IR 1310, page D-136

???D.4.9 Slot Properties???OC48 LR 1550, page D-145

???D.4.10 Slot Properties???OECP-L, page D-153

???D.4.11 Slot Properties???S1.1-2-LC (ONS 15305 CTC), page D-156

???D.4.12 Slot Properties???S1.1-8-LC (ONS 15305 CTC), page D-158

???D.4.13 Slot Properties???S16.1-1-LC (ONS 15305 CTC), page D-160

???D.4.14 Slot Properties???STM-1, page D-162

???D.4.15 Slot Properties???STM-1 S1.1-2-LC/E1-21 (ONS 15305 CTC), page D-168

???D.4.16 Slot Properties???STM-1E-12, page D-170

???D.4.17 Slot Properties???STM-16 (ONS 15454 SDH), page D-176

???D.4.18 Slot Properties???STM-16 (ONS 15600 SDH), page D-181

???D.4.19 Slot Properties???STM-4 IR/STM4 SH 1310, page D-189

???D.4.20 Slot Properties???STM-4 L4.2-2-LC (ONS 15305 CTC), page D-195

???D.4.21 Slot Properties???STM-16 L16.2-1-LC (ONS 15305 CTC), page D-197

???D.4.22 Slot Properties???STM-64 LH 1550 (ONS 15454 SDH), page D-199

???D.4.23 Slot Properties???STM-64 LR/LH 4 (ONS 15600 SDH), page D-205

D.4.1 Slot Properties???OC12 IR/STM4 SH 1310

The Slot Properties pane displays information about the Cisco ONS 15327 or ONS 15454 slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The ONS 15454 Optical Connector (OC12 IR/STM4 SH 1310) card provides one intermediate or short range SONET/SDH OC-12 port compliant with the International Telecommunication Union (ITU) G.707, ITU-T G.957, and Telcordia GR-253-CORE. The port operates at 622.08 Mbps over a single-mode fiber span. The card supports VT and nonconcatenated or concatenated payloads at STS-1, STS-3c, STS-6c, or STS-12c signal levels.

For the OC12 IR/STM4 SH 1310 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, and Info.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.1.8 Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.2 Slot Properties???OC12-4 IR/STM4 SH 1310

The Slot Properties pane displays information about the Cisco ONS 15327 or ONS 15454 slot that is selected in the NE Explorer tree. Use this properties pane to change the module's performance monitoring thresholds.

The Optical Connector (OC12-4 IR/STM4 SH 1310) card provides one intermediate or short range SONET/SDH OC-12 port compliant with the International Telecommunication Union???s G.707, G.957, and Telcordia???s GR-253. The port operates at 622.08 Mbps over a single-mode fiber span. The card supports VT and nonconcatenated or concatenated payloads at STS-1, STS-3c, STS-6c, or STS-12c signal levels.

For the OC12-4 IR/STM4 SH 1310 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, J1 Path Trace, and Info.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-97 Field Descriptions for the Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.3 Slot Properties???OC192 LR/STM64 LH 1550

The Slot Properties pane displays information about the Cisco ONS 15454 SONET, ONS 15454 SDH, or ONS 15600 slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The OC192 LR/STM64 LH 1550 card provides one long-range SONET/SDH OC-192 port compliant with the International Telecommunication Union (ITU-T) G.707, ITU-T G.957, Telcordia GR-1377-CORE, and Telcordia GR-253-CORE. The card port operates at 9.96 Gbps over unamplified distances up to 80 km when using fiber such as C-SMF or dispersion compensated fiber limited by loss and/or dispersion. The card supports VT and nonconcatenated or concatenated payloads.

For the OC192 LR/STM64 LH 1550 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and J1 Path Trace.

D.4.3.1 Module View Tab

The Module View tab displays a graphic of the OC192 LR/STM64 LH 1550 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

D.4.3.2 Identification Tab

The Identification tab allows you to view and update OC192 LR/STM64 LH 1550 identification information.

Table D-98 Field Descriptions for the Identi???cation Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.3.5 Loopback Tab

The Loopback tab allows you to view and update OC192 LR/STM64 LH 1550 loopback information.

Table D-101 Field Descriptions for the Loopback Tab

D.4.3.6 Protection Tab

The Protection tab allows you to view and update OC192 LR/STM64 LH 1550 protection group information.

Table D-102 Field Descriptions for the Protection Tab

D.4.3.7 Alarm Behavior Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.4 Slot Properties???OC192/STM64 XFR-Based

The OC-192/STM64 XFR-based card is an OC-192/STM-64 card based on XFP optics for use in ONS 15454 SONET or ONS 15454 SDH shelves. It is a one-base OC-192/STM-64 board that can be used with SR, IR, or LR XFP optics modules.

For the OC192/STM64 XFR-based module, the Slot Properties pane displays the following tabs: Module View, Identification, Pluggable Provisioning, Line, VC-4, STS, Loopback, Protection, Alarm Behavior, Transceiver, Auto Laser Shutdown, Section Trace, J1 Path Trace, and Info.

D.4.4.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.4.3.1 Provision Pluggable Dialog Box

D.4.4.4 Line (ONS 15454 SONET) Tab

The Line tab allows you to view and update OC192/STM64 XFR-based card optical line performance monitoring information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.4.15 Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.5 Slot Properties???OC3 IR 4 1310

The Optical Connector (OC3 IR 4/STM1 SH 1310) card provides four intermediate or short range SONET/SDH OC-3 ports compliant with the International Telecommunication Union (ITU-T) G.707, ITU-T G.957, and Telcordia GR-253-CORE. Each port operates at 155.52 Mbps over a single-mode fiber span. The card supports VT and nonconcatenated or concatenated payloads at the STS-1 or STS-3c signal levels.

For the OC3 IR 4/STM1 SH 1310 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, J1 Path Trace, and Info.

D.4.5.1 Module View Tab

The Module View tab displays a graphic of the OC3 IR 4/STM1 SH 1310 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

D.4.5.2 Identification Tab

The Identification tab allows you to view and update OC3 IR 4/STM1 SH 1310 identification information.

Table D-120 Field Descriptions for the Identi???cation Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-121 Field Descriptions for the Line Tab (continued)

D.4.5.4 STS Tab

The STS tab allows you to view and update OC3 IR 4/STM1 SH 1310 STS information.

Table D-122 Field Descriptions for the STS Tab

STS Config

Displays the STS number, the intermediate path protection monitoring (IPPM) status, and XC loopback status.

Path Thresh 15 Min

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.5.7 Alarm Behavior Tab

D.4.5.8 J1 Path Trace Tab

The J1 Path Trace tab allows you to view and update OC3 IR 4/STM1 SH 1310 J1 path trace information.

Note This tab is not available on ONS 15327 OC3 IR 4/STM1 SH 1310 cards.

D.4.5.9 Info Tab

The Info tab allows you to view nominal operating values set during manufacturing for the OC3 IR 4/STM1 SH 1310 module.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-127 Field Descriptions for the Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.6 Slot Properties???OC3 IR/STM1 SH 1310-8

The Slot Properties pane displays information about the Cisco ONS 15454 SONET or ONS 15454 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The OC3 IR/STM1 SH 1310-8 card provides eight intermediate or short range SONET/SDH OC-3 ports compliant with ITU-T G.707, ITU-T G.957, and Telcordia GR-253-CORE. Each port operates at 155.52 Mbps over a single-mode fiber span. The card supports VT and nonconcatenated or concatenated payloads at the STS-1 or STS-3c signal levels.

For the OC3 IR/STM1 SH 1310-8 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, J1 Path Trace, and Info.

D.4.6.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-129 Field Descriptions for the Line Tab (continued)

D.4.6.4 STS Tab

The STS tab allows you to view and update OC3 IR/STM1 SH 1310-8 STS information.

Table D-130 Field Descriptions for the STS Tab

STS Config

Displays the STS number, the intermediate path protection monitoring (IPPM) status, and XC loopback status.

Path Thresh 15 Min

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.6.10 Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.7 Slot Properties???OC48

The Slot Properties pane displays information about the Cisco ONS 15600 slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

For the OC48 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Transceiver, Protection, Alarm Behavior, and J1 Path Trace.

D.4.7.1 Module View Tab

The Module View tab displays a graphic of the OC48 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.7.5 Loopback Tab

The Loopback tab allows you to view and update OC48 loopback information.

Table D-140 Field Descriptions for the Loopback Tab

D.4.7.6 Transceiver Tab

The Transceiver tab allows you to view and update OC48 transceiver information.

D.4.7.7 Protection Tab

The Protection tab allows you to view and update OC48 protection group information.

Table D-142 Field Descriptions for the Protection Tab

D.4.7.8 Alarm Behavior Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.7.9 J1 Path Trace Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.8 Slot Properties???OC48 IR 1310

The ONS 15454 Optical Connector (OC48 IR 1310) card provides one intermediate-range, Telcordia GR-253-CORE compliant SONET OC-48 port per card. Each port operates at 2.49 Gbps over a single-mode fiber span. The card supports VT, nonconcatenated, or concatenated payloads at STS-1, STS-3c, STS-6c, STS-12c, or STS-48c signal levels.

For the OC48 IR 1310 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and J1 Path Trace.

Note The OC48 any slot (AS) card supports J1 path trace, but the OC48 card does not.

D.4.8.1 Module View Tab

The Module View tab displays a graphic of the OC48 IR 1310 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.8.5 Loopback Tab

The Loopback tab allows you to view and update OC48 IR 1310 loopback information.

Table D-148 Field Descriptions for the Loopback Tab

D.4.8.6 Protection Tab

The Protection tab allows you to view and update OC48 IR 1310 protection group information.

Table D-149 Field Descriptions for the Protection Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.8.7 Alarm Behavior Tab

D.4.8.8 Auto Laser Shutdown Tab

D.4.8.9 J1 Path Trace Tab

The J1 Path Trace tab allows you to view and update OC48 IR 1310 J1 path trace information.

Note This tab is not available on ONS 15327 OC48 IR 1310 cards.

Note The OC48_AS card supports J1 path trace, but the OC48 card does not.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.9 Slot Properties???OC48 LR 1550

The OC48 LR 1550 card provides one long-range, SONET OC-48 port per card, compliant with Telcordia GR-253-CORE. Each port operates at 2.49 Gbps over a single-mode fiber span. The card supports VT, nonconcatenated or concatenated payloads at STS-1, STS-3c, STS-6c, STS-12c, or STS-48c signal levels.

For the OC48 LR 1550 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, STS, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and Info.

Note The OC48 any slot (AS) card supports J1 path trace, but the OC48 card does not.

D.4.9.1 Module View Tab

The Module View tab displays a graphic of the OC48 LR 1550 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-160 Field Descriptions for the Info Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.10 Slot Properties???OECP-L

The Slot Properties pane displays information about the Cisco ONS 15808 module that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The Odd/Even Channel Processor???L band???Active (OECP-L) and Odd/Even Channel Processor???L band???Passive (OECP-L-P) modules are bidirectional multiplexer/demultiplexers. On the transmit side, the OECP-L-P module multiplexes the 20 odd-numbered channel signal and the 20 even-numbered channel signal into a composite 40-channel signal. The channels in the 20-channel signal are spaced at 100 GHz. The channels in the 40-channel composite signal are spaced at 50 GHz. On the receive side, the OECP-L module demultiplexes the composite 40-channel signal into two separate 20-channel signals.

Note Operating temperature is monitored on the L-band boards only when they are configured as ACTIVE (OECP-L).

The card faceplate is shown in the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Figure D-1 Cisco ONS 15808 Odd/Even Channel Processor???L Band

OECP-L modules shown on this sheet include:

???Odd/Even Channel Processor???L band???Active (OECP-L)

???Odd/Even Channel Processor???L band???Passive (OECP-L--P)

For ONS 15808 OECP-L modules, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, and Input Power.

D.4.10.1 Module View Tab

The Module View tab displays a graphic of the OECP-L module that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table, in the Alarm Browser, or in the OECP PM Table.

D.4.10.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.11 Slot Properties???S1.1-2-LC (ONS 15305 CTC)

The Slot Properties pane displays information about the Cisco ONS 15305 CTC slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The two optical STM-1 interfaces use a dual-fiber interface, an LC-style connector, one fiber in each direction, 1310 nm wavelength, and single-mode fiber of type 10/125 nm. The optical interfaces are compatible with ITU-T 957 for S-1.1.

The interface is an optical STM-1 short-haul interface, according to clause 5 ITU-T G.957. The definitions of optical parameters and reference points S and R refer to ITU-T G.957. Reference point S is the transmit direction; reference point R is the receive direction of the fiber. A module diagram is shown in the following figure.

Figure D-2 S1.1-2-LC Module

S16.1-2-LC

MOD

FAIL

CLASS 1

LASER

PRODUCT

MOD

DIS

96699

For the S1.1-2-LC module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, VC-4 Config, and Loopback. The tabs shown depend on the NE configuration.

D.4.11.1 Module View Tab

The Module View tab displays a graphic of the S1.1-2-LC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.11.4 VC-4 Config Tab

D.4.11.5 Loopback Tab

The Loopback tab allows you to view and update STM-1 loopback information.

Table D-167 Field Descriptions for the Loopback Tab

D.4.12 Slot Properties???S1.1-8-LC (ONS 15305 CTC)

The module contains eight optical STM-1 interfaces that meets the S-1.1 specification in ITU-T G.957. The physical connector is an LC connector. The module also contains 8 mapper circuits and an IP switch, allowing concentration of IP traffic mapped into VC-12 container. Since the mapper circuits are connected to the matrix, the mapper circuits are global resources which means that the traffic to be terminated may come from other modules in the system. A module diagram is shown in the following figure.

Figure D-3 Octal Optical S-1.1 Module, S1.1-8-LC

90891

The Slot Properties pane displays information about the slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

For the S1.1-8-LC module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, and WAN Line. The tabs shown depend on the NE configuration.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.12.4 WAN Line Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.13 Slot Properties???S16.1-1-LC (ONS 15305 CTC)

The S16.1-1-LC module contains one optical STM-16 interfaces that meets the S-16.1 specification in ITU-T G.957. The physical connector is an LC connector. The module only supports TDM traffic.

Figure D-4 Single Optical S-16.1 Module, S16.1-1-LC

S16.1-1-LC

MOD

FAIL

CLASS 1

LASER

PRODUCT

96701

For the S16.1-1-LC module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, VC-4 Config, and Loopback.

D.4.13.1 Module View Tab

The Module View tab displays a graphic of the S16.1-1-LC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.13.4 VC-4 Config Tab

D.4.13.5 Loopback Tab

The Loopback tab allows you to view and update S16.1-1-LC loopback information.

Table D-174 Field Descriptions for the Loopback Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.14 Slot Properties???STM-1

The STM-1 IR 4/STM1 SH 1310 (STM1_4 and STM1_8) card provides four or eight intermediate or short range, ITU-T G.707-, ITU-T G.957-compliant, SDH STM-1 ports. Each port operates at 155.52 Mbps over a single-mode fiber span. The card supports concatenated or nonconcatenated payloads at the STM-1 signal level on a per-VC-4 basis.

For the STM-1 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and J1 Path Trace. The tabs shown depend on the NE configuration.

D.4.14.1 Module View Tab

The Module View tab displays a graphic of the STM-1 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.14.4 VC-4 Tab

Displays the VC-4 number, the intermediate path protection monitoring (IPPM) status, and the XC loopback status. The XC Loopback field only appears on ONS 15454 SDH Release 4.0.

Threshold 15 Minutes

D.4.14.5 Loopback Tab

The Loopback tab allows you to view and update STM-1 loopback information.

Table D-178 Field Descriptions for the Loopback Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.14.9 J1 Path Trace Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.15 Slot Properties???STM-1 S1.1-2-LC/E1-21 (ONS 15305 CTC)

The module contains two optical STM-1 short-haul interfaces and 21 E1 interfaces. The main functions of the module are O/E- E/O conversion and SDH multi/demultiplexing with VC-12, VC-3 and VC-4 granularity of the STM-1 traffic and VC-12 mapping/demapping demultiplexing of the E1 traffic. The module supports both transparent E1 data transmission according to ITU-T Rec. G.703 as well as the NT functionality of ISDN PRA according to ETSI 300 233. One high density LFH type connector is used to interface the 21 E1s, and a dual-fiber LC connector (one fiber in each direction) is used on the two STM1 interfaces. A module diagram is shown in the following figure.

Figure D-5

OUT IN 1

STM-1 S1.1-2-LC/E1-21 Module

For the S1.1-2-LC/E1-21 module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, and E1 Line. The tabs shown depend on the NE configuration.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.15.4 E1 Line Tab

D.4.16 Slot Properties???STM-1E-12

The twelve-port ONS 15454 SDH STM-1E-12 card provides twelve ITU-compliant, G.703 STM-1 ports per card. For release 5.0 NEs and earlier, ports 9 to 12 can be switched to E-4 instead of STM-1. Each interface operates at 155.52 Mbps for STM-1 or 139.264 Mbps for E-4 over a 75-ohm coaxial cable (with the FMEC STM1E NP card, the FMEC STM1E 1:1 card, or the FMEC STM1E 1:3 card). In E-4 mode, framed or unframed signal operation is possible. The STM1E-12 card operates as a working or protect card in 1:1 and in 1:3 protection schemes.

Note For release 6.0 NEs, E-4 provisioning is not supported; all ports 1 to 12 are STM-1.

For the STM-1E-12 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Protection, Alarm Behavior, and J1 Path Trace.

D.4.16.1 Module View Tab

The Module View tab displays a graphic of the STM1E-12 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-187 Field Descriptions for the Line Tab (continued)

D.4.16.4 VC-4 Tab

The VC-4 tab allows you to view and update STM-1E-12 VC-4 information.

Table D-188 Field Descriptions for the VC-4 Tab

VC-4

Displays the VC-4 number, the intermediate path protection monitoring (IPPM) status, and the XC loopback status.

Threshold 15 Minutes

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.17 Slot Properties???STM-16 (ONS 15454 SDH)

The OC48 IR/STM16 SH AS 1310 card provides one intermediate-range, ITU-T G.707, ITU-T G.957-compliant, SDH STM-16 port per card. The interface operates at 2.488 Gbps over a single-mode fiber span. The card supports concatenated or nonconcatenated payloads at STM-1, STM-4, or STM-16 signal levels on a per-VC-4 basis.

For the STM-16 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and J1 Path Trace.

D.4.17.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.17.5 Loopback Tab

The Loopback tab allows you to view and update STM-16 loopback information.

Table D-196 Field Descriptions for the Loopback Tab

D.4.17.6 Protection Tab

The Protection tab allows you to view and update STM-16 protection group information.

Table D-197 Field Descriptions for the Protection Tab

D.4.17.7 Alarm Behavior Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.17.8 Auto Laser Shutdown Tab

D.4.17.9 J1 Path Trace Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.18 Slot Properties???STM-16 (ONS 15600 SDH)

The Slot Properties pane displays information about the Cisco ONS 15600 SDH slot that is selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

The STM-16 card provides 16 long-haul STM-16 ITU-T G.957 L-16.2 compliant signals. The ports operate at the ITU-T G.707 compliant 2488.32 Mbps rate over a single-mode fiber span. The card has four physical connector adapters with eight fibers per connector adapter. The card VC4 payloads and concatenated payloads at VC4, VC4-4c, VC4-8c, or VC4-16c signal levels.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.18.6 Transceiver Tab

The Transceiver tab allows you to view and update STM-16 transceiver information.

D.4.18.7 Protection Tab

The Protection tab allows you to view and update STM-16 protection group information.

Table D-206 Field Descriptions for the Protection Tab

D.4.18.8 Alarm Behavior Tab

D.4.18.9 J1 Path Trace Tab

The J1 Path Trace tab allows you to view and retrieve STM-16 J1 path trace information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.19 Slot Properties???STM-4 IR/STM4 SH 1310

The STM-4 IR/STM4 SH 1310 (STM4_1 and STM4_4) card provides one or four intermediate or short range, ITU-T G.707, ITU-T G.957-compliant, SDH STM-4 ports per card. The interface operates at 622.08 Mbps over a single-mode fiber span. The card supports concatenated or nonconcatenated payloads on a per-VC-4 basis.

For the STM-4 IR/STM4 SH 1310 card, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Protection, Alarm Behavior, and J1 Path Trace.

D.4.19.1 Module View Tab

The Module View tab displays a graphic of the STM-4 IR/STM4 SH 1310 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.19.4 VC-4 Tab

Displays the VC-4 number, the intermediate path protection monitoring (IPPM) status, and the XC loopback status.

Threshold 15 Minutes

D.4.19.5 Loopback Tab

The Loopback tab allows you to view and update STM-4 IR/STM4 SH 1310 loopback information.

Table D-212 Field Descriptions for the Loopback Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.19.6 Protection Tab

The Protection tab allows you to view and update STM-4 IR/STM4 SH 1310 protection group information.

Table D-213 Field Descriptions for the Protection Tab

D.4.19.7 Alarm Behavior Tab

D.4.19.8 J1 Path Trace Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.20 Slot Properties???STM-4 L4.2-2-LC (ONS 15305 CTC)

This is a dual-port STM4 module for long-haul transmission at 1550 nm optical wavelength. The main functions of the module are O/E-E/O conversion and SDH multi/demultiplexing with VC-12, VC-3, and VC-4 granularity. A module diagram is shown in the following figure.

Figure D-6 STM-4 L4.2-2-LC Module

STM-4 L4.2-2-LC

MOD

FAIL

CLASS 1

LASER

PRODUCT

MOD

DIS

102181

For the L4.2-2-LC module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, VC-4 Config and Loopback.

D.4.20.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

Table D-219 Field Descriptions for the Loopback Tab (continued)

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.21 Slot Properties???STM-16 L16.2-1-LC (ONS 15305 CTC)

This is an STM16 long-haul module for transmission at 1550 nm optical wavelength. The main functions of the module are O/E- E/O conversion and SDH multi/demultiplexing with VC-12, VC-3 and VC-4 granularity.

A module diagram is shown in the following figure.

Figure D-7

STM-16 L16.2-1-LC

MOD

FAIL

STM-16 L16.2-1-LC Module

CLASS 1

LASER

PRODUCT

For the L16.2-1-LC module, the Slot Properties pane displays the following tabs: Module View, Identification, STM Line, VC-4 Config and Loopback.

D.4.21.1 Module View Tab

The Module View tab displays a graphic of the L16.2-1-LC that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to add, delete, change, or reset the module.

D.4.21.2 Identification Tab

The Identification tab allows you to view and update L16.2-1-LC identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.21.5 Loopback Tab

The Loopback tab allows you to view and update L16.2-1-LC loopback information.

Table D-223 Field Descriptions for the Loopback Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.22 Slot Properties???STM-64 LH 1550 (ONS 15454 SDH)

The STM-64 LH 1550 card provides one long-range SONET/SDH STM64 port compliant with the International Telecommunication Union (ITU-T) G.707, ITU-T G.957, Telcordia GR-1377-CORE, and Telcordia GR-253-CORE. The card port operates at 9.96 Gbps over unamplified distances up to 80 km when using fiber such as C-SMF or dispersion compensated fiber limited by loss and/or dispersion. The card supports VT and nonconcatenated or concatenated payloads.

For the STM-64 LH 1550 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Protection, Alarm Behavior, Auto Laser Shutdown, and J1 Path Trace.

D.4.22.1 Module View Tab

The Module View tab displays a graphic of the STM-64 LH 1550 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s).

D.4.22.2 Identification Tab

The Identification tab allows you to view and update STM-64 LH 1550 identification information.

Table D-224 Field Descriptions for the Identi???cation Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.22.4 VC-4 Tab

Displays the VC-4 number, the intermediate path protection monitoring (IPPM) status, and the XC loopback status. The XC Loopback field only appears on the ONS 15454 SDH R4.0.

Path Threshold 15 Minutes

D.4.22.5 Loopback Tab

The Loopback tab allows you to view and update STM-64 LH 1550 loopback information.

Table D-227 Field Descriptions for the Loopback Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Optical Cards

D.4.22.9 J1 Path Trace Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.4.23 Slot Properties???STM-64 LR/LH 4 (ONS 15600 SDH)

The STM-64 LR/LH 4 port 1550 card provides 4 long-haul STM-64 ITU-T G.9691 L-64.2c compliant signals. The ports operate at the ITU-T G.707 compliant 9953.28 Mbps rate over a single-mode fiber span. The card has four physical connector adapters with 2 fibers per connector adapter. The card VC4 payloads and concatenated payloads at VC4, VC4-4c, VC4-8c, VC4-16c, or VC-64c signal levels.

For the STM-64 LR/LH 4 module, the Slot Properties pane displays the following tabs: Module View, Identification, Line, VC-4, Loopback, Transceiver, Protection, Alarm Behavior, and J1 Path Trace.

D.4.23.1 Module View Tab

The Module View tab displays a graphic of the STM-64 LR/LH 4 that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Alarms are also displayed when you move the mouse pointer over the graphic.) The Suppress Alarms check box is read-only and indicates whether all alarms are suppressed for the card and its port(s). Right-clicking the graphic opens a shortcut menu that you can use to reset, delete, or change the card.

D.4.23.2 Identification Tab

The Identification tab allows you to view and update STM-64 LR/LH 4 identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5 Transponder Cards

This section describes the following transponder cards supported within CTM:

???D.5.1 Slot Properties???BT10E-LCxx and BT10E-LLxx, page D-213

???D.5.2 Slot Properties???FEC-LEM, page D-219

???D.5.3 Slot Properties???LEM, page D-223

???D.5.4 Slot Properties???LEM-10-B1, page D-225

???D.5.5 Slot Properties???LEM-10G-Nxx, page D-229

???D.5.6 Slot Properties???LEM-EM-M, page D-232

???D.5.7 Slot Properties???LT, page D-235

???D.5.8 Slot Properties???RT, page D-240

???D.5.9 Slot Properties???RXT, page D-244

???D.5.10 Slot Properties???RXT-10G-N, page D-246

???D.5.11 Slot Properties???RXT-10H-M, page D-249

???D.5.12 Slot Properties???RXT-B1, page D-252

???D.5.13 Slot Properties???RXT-FEC, page D-256

???D.5.14 Slot Properties???Transmitter Transponder, page D-259

???D.5.15 Slot Properties???WCM, page D-264

???D.5.16 Slot Properties???WCM-10G-Nxx, page D-267

???D.5.17 Slot Properties???WCM-FEC, page D-270

???D.5.18 Slot Properties???WCM-EM-Fxx, page D-274

???D.5.19 Slot Properties???WCM-EM-Mxx, page D-279

???D.5.20 Slot Properties???WCM10, page D-283

D.5.1 Slot Properties???BT10E-LCxx and BT10E-LLxx

The bidirectional line transponder (BT10E-LCxx and BT10E-LLxx) performs a rate adaptation between the 10 GE client interface (10.312 Gbps) and the FEC payload rate (9.9532 Gbps). The BT10E-LCxx and BT10E-LLxx support a constant flow of maximum Ethernet packet length (1518 bytes) with a minimum average IPG =10.5. BT10E cards can support jumbo frames with a maximum packet length of 12000 bytes.

The Slot Properties pane displays the following tabs: Module View, Identification, Transmit Direction, Receive Direction, and Action.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.1.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table, in the Alarm Browser, or in the BT Transponder PM Table.

D.5.1.2 Identification Tab

D.5.1.3 Transmit Direction Tab

The Transmit Direction tab allows you to configure the BT10E-LCxx and BT10E-LLxx transmit direction properties. The tab contains the following subtabs:

???D.5.1.3.1 Temperature Subtab, page D-215

???D.5.1.3.2 Current Subtab, page D-215

???D.5.1.3.3 Power Subtab, page D-215

???D.5.1.3.4 Input Power Subtab, page D-215

???D.5.1.3.5 Output Power Subtab, page D-216

???D.5.1.3.6 QoS 15 Min and QoS 1 Day Subtabs, page D-216

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.1.3.1 Temperature Subtab

The Temperature subtab allows you to assign temperature-related thresholds and alarm severities for the transponder laser.

Table D-241 Field Descriptions for the Temperature Subtab

D.5.1.3.2 Current Subtab

The Current subtab allows you to assign thresholds and alarm severities for the transponder laser current levels.

Table D-242 Field Descriptions for the Current Subtab

D.5.1.3.3 Power Subtab

The Power subtab allows you to assign thresholds and alarm severities for the transponder laser power levels.

Table D-243 Field Descriptions for the Power Subtab

D.5.1.3.4 Input Power Subtab

The Input Power subtab allows you to assign thresholds and alarm severities for the power coming into the transponder lasers.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-244 Field Descriptions for the Input Power Subtab

Field Description

Input Power 1

D.5.1.3.5 Output Power Subtab

The Output Power subtab allows you to assign thresholds and alarm severities for the transponder output power.

Table D-245 Field Descriptions for the Output Power Subtab

Field Description

Output Power

D.5.1.3.6 QoS 15 Min and QoS 1 Day Subtabs

The QoS 15 Min and QoS 1 Day subtabs allow you to assign thresholds and alarm severities for quality of service (QoS) counters. Click the QoS 15 min tab to assign thresholds for 15-minute collection increments. Click the QoS 1 day tab to assign thresholds for 24-hour collection increments. The two tabs have identical fields.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.1.4 Receive Direction Tab

The Receive Direction tab allows you to configure the BT10E-LCxx and BT10E-LLxx receive direction properties. The Receive Direction tab contains the following subtabs:

???D.5.1.4.1 Input Power Subtab, page D-217

???D.5.1.4.2 Output Power Subtab, page D-217

???D.5.1.4.3 QoS 15 Min and QoS 1 Day Subtabs, page D-217

D.5.1.4.1 Input Power Subtab

The Input Power subtab allows you to assign thresholds and alarm severities for the power coming into the transponder lasers.

Table D-247 Field Descriptions for the Input Power Subtab

Field Description

Input Power 1

D.5.1.4.2 Output Power Subtab

The Output Power subtab allows you to assign thresholds and alarm severities for the transponder output power.

Table D-248 Field Descriptions for the Output Power Subtab

Field Description

Output Power 1

D.5.1.4.3 QoS 15 Min and QoS 1 Day Subtabs

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.2 Slot Properties???FEC-LEM

The Slot Properties pane displays information about the Cisco ONS 15800 or ONS 15801 module that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module???s performance monitoring thresholds.

Forward error correction (FEC) line extender modules (LEMs) extend transmission distances in ONS 15800 or ONS 15801 regeneration and optical add/drop multiplexing (OADM) sites.

A block diagram is shown in the following figure.

Figure D-8 Cisco ONS 15800 or ONS 15801 FEC Line Extender Module

The ONS 15800 or ONS 15801 transponder modules shown on this sheet include:

???Line Extender Module???Externally Modulated???2.5 Gbps???FEC (LEM-EM-Fxx)

???Line Extender Module???Externally Modulated???10 Gbps???FEC (LEM-10G-Fxx)

For FEC-LEM transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, Output Power, and Action.

D.5.2.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, Equipment Inventory Table, or in the FEC-LEM PM Table.

D.5.2.2 Identification Tab

The Identification tab allows you to view and update transponder identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.2.3 Temperature Tab

The Temperature tab allows you to assign temperature-related thresholds and alarm severities for the transponder laser.

Table D-252 Field Descriptions for the Temperature Tab

D.5.2.4 Quality of Service Tab

The Quality of Service tab allows you to assign thresholds and alarm severities for forward error correction (FEC) counters. Click the 15 min radio button to assign thresholds for 15-minute collection increments. Click the 1 day radio button to assign thresholds for 24-hour collection increments.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.2.7 Input Power Tab

D.5.2.8 Output Power Tab

D.5.2.9 Action Tab

The Action tab allows you to specify the output power setting.

Table D-258 Field Descriptions for the Action Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.3 Slot Properties???LEM

Line extender modules (LEMs) extend transmission distances in ONS 15800 or ONS 15801 regeneration and optical add/drop multiplexing (OADM) sites.

A block diagram is shown in the following figure.

Figure D-9 Cisco ONS 15800 or ONS 15801 Line Extender Module

The ONS 15800 or ONS 15801 LEM modules shown on this sheet include:

???Line Extender Module???Externally Modulated???Normal (LEM-EM-Nxx)

???Line Extender Module???622 Mbps???Normal (LEM-622-Nxx)

For these transponders, the Slot Properties pane displays the following tabs: Module View,

Identification, Temperature, Current, Power, Input Power, and Output Power.

D.5.3.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, and minor alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser or in the Equipment Inventory Table.

D.5.3.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.3.3 Temperature Tab

The Temperature tab allows you to assign thresholds and alarm severities for the transponder laser.

Table D-260 Field Descriptions for the Temperature Tab

D.5.3.4 Current Tab

D.5.3.5 Power Tab

The Power tab allows you to assign thresholds and alarm severities for the transponder Laser 1 power levels.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.3.6 Input Power Tab

D.5.3.7 Output Power Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.4 Slot Properties???LEM-10-B1

Line extender modules (LEMs) extend transmission distances in ONS 15800 or ONS 15801 regeneration and optical add/drop multiplexing (OADM) sites.

A block diagram is shown is the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Figure D-10 Cisco ONS 15800 or ONS 15801 Line Extender Module???10-Gbps???B1 Monitoring

The ONS 15800 or ONS 15801 transponder modules shown on this sheet include:

???Line Extender Module???10 Gbps???B1 Monitoring (LEM-10G-Mxx)

???Line Extender Module???10 Gbps High Output Power???B1 Monitoring (LEM-10H-Mxx)

For these transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.4.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the B1 LEM PM Table.

D.5.4.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.4.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the transponder laser temperature.

Table D-266 Field Descriptions for the Temperature Tab

D.5.4.4 Quality of Service Tab

The Quality of Service tab allows you to assign thresholds and alarm severities for B1 counters. Click the 15 min radio button to assign thresholds for 15-minute collection increments. Click the 1 day radio button to assign thresholds for 24-hour collection increments.

Table D-267 Field Descriptions for the Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-267 Field Descriptions for the Quality of Service Tab (continued)

D.5.4.5 Current Tab

D.5.4.6 Power Tab

D.5.4.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the transponder.

Table D-270 Field Descriptions for the Input Power Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.4.8 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the transponder output power.

Table D-271 Field Descriptions for the Output Power Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.5 Slot Properties???LEM-10G-Nxx

The Slot Properties pane displays information about the Line Extender Module???10 Gbps???Normal (LEM-10G-Nxx) that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

Line extender modules (LEMs) extend transmission distances in Cisco ONS 15800 or ONS 15801 regeneration and optical add/drop multiplexing (OADM) sites.

A block diagram is shown in the following figure.

Figure D-11 Cisco ONS 15800 or ONS 15801 Line Extender Module???10 Gbps???Normal

For the LEM-10G-Nxx module, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Current, Power, Input Power, and Output Power.

D.5.5.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table or in the Alarm Browser.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.6 Slot Properties???LEM-EM-M

The Slot Properties pane displays information about the Line Extender Module???Externally Modulated???B1 Monitoring (LEM-EM-M) that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

Line extender modules (LEMs) extend transmission distances in Cisco ONS 15800 or ONS 15801 regeneration and optical add/drop multiplexing (OADM) sites.

A block diagram is shown in the following figure.

Figure D-12 Cisco ONS 15800 or ONS 15801 Line Extender Module???Externally Modulated???B1 Monitoring

For the B1 LEM transponder, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.6.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser or in the Equipment Inventory Table.

D.5.6.2 Identification Tab

The Identification tab allows you to view and update transponder identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.6.5 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the transponder laser current levels.

Table D-281 Field Descriptions for the Current Tab

D.5.6.6 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the transponder Laser 1 power levels.

Table D-282 Field Descriptions for the Power Tab

D.5.6.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the transponder.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.6.8 Output Power Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.7 Slot Properties???LT

The line transponder performs 3R regeneration of 2.5 Gbps and 10 Gbps optical signals and provides performance and quality parameters based on forward error correction (FEC) overhead. Line transponders are used in regeneration sites to retime, reshape, and regenerate low output signals. Line transponders decode out-of-band (OOB) FEC information, perform error correction, and add OOB-FEC encoding to transport signals.

A block diagram is shown in the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Figure D-13 Cisco ONS 15808 Line Transponder

Line transponders shown on this sheet include:

???Line Transponder???2.5 Gbps???C band (LT-25G-Cxx)

???Line Transponder???10 Gbps???C band (LT-10G-Cxx)

???Line Transponder???10 Gbps???C band???Single Slot (LT-10G-SCxx)

???Line Transponder???10 Gbps???L band???Single Slot (LT-10G-SLxx)

For ONS 15808 line transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, Output Power, and Action.

D.5.7.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table, in the Alarm Browser, or in the Line Transponders PM Table.

D.5.7.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.7.3 Temperature Tab

D.5.7.4 Quality of Service Tab

Table D-287 Field Descriptions for the Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.7.5 Current Tab

The Current tab allows you to assign thresholds and alarm severities for the transponder laser current levels.

Table D-288 Field Descriptions for the Current Tab

D.5.7.6 Power Tab

D.5.7.7 Input Power Tab

The Input Power tab allows you to assign thresholds and alarm severities for the power coming into the transponder lasers.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-290 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.7.8 Output Power Tab

The Output Power tab allows you to assign thresholds and alarm severities for the transponder output power.

Table D-291 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

D.5.7.9 Action Tab

The Action tab allows you to force the ONS 15808 optical output power.

Table D-292 Field Descriptions for the Action Tab

FieldDescription

Output Power Setting

???The equalization of the channel downstream from the optical line, the optical channel S/N in fiber, and at the end of the optical line.

???The optical channel power at the end of the optical line.

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.8 Slot Properties???RT

The receiver transponder is used in terminal sites (receive direction) and in OADM sites to retime, reshape, and regenerate 2.5 Gbps and 10 Gbps low-input signals. Receiver transponders perform 3R regeneration of optical signals and provide quality parameters based on forward error correction (FEC) overhead and client signal validation parameters. Receiver transponders perform out-of-band (OOB) FEC decoding and error correction for transport signals, which are transmitted to SONET- or SDH-compliant client equipment. The interface complies with Bellcore GR-253 and ITU-T G.957 SONET and SDH physical interface specifications.

A block diagram is shown in the following figure.

Figure D-14 Cisco ONS 15808 Receiver Transponder

Receiver transponders shown on this sheet include:

???Receive Transponder???2.5 Gbps???C band???FEC Coding (RT-25G-Cxx)

???Receive Transponder???10 Gbps???C band???FEC Coding (RT-10G-Cxx)

???Receive Transponder???10 Gbps???C band???Single Slot 1300 nm (RT-10G-13Cxx)

???Receive Transponder???10 Gbps???L band???Single Slot 1300 nm (RT-10G-13Lxx)

???Receive Transponder???10 Gbps???C band???Single Slot???FEC Coding (RT-10G-SCxx)

???Receive Transponder???10 Gbps???L band???Single Slot???FEC Coding (RT-10G-SLxx)

For ONS 15808 receiver transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.8.1 Module View Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.8.5 Power Tab

D.5.8.6 Input Power Tab

The Input Power tab allows you to assign thresholds and alarm severities for the power coming into the transponder lasers.

Table D-297 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.8.7 Output Power Tab

The Output Power tab allows you to assign thresholds and alarm severities for the transponder output power.

Table D-298 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.9 Slot Properties???RXT

Cisco ONS 15800 and ONS 15801 Receive Transponder (RXT) modules are used in Cisco ONS 15800 and ONS 15801 terminal sites to retime, reshape, and regenerate low input demultiplexed signals.

A block diagram is shown in the following figure.

Figure D-15 Cisco ONS 15800 or ONS 15801 Receive Transponder

RXT modules shown on this sheet include:

???Receive Transponder???Directly Modulated???Normal module (RXT-DM-N)

???Receive Transponder???622 Mbps???Normal module (RXT-622-N)

For these RXT modules, the Slot Properties pane displays the following tabs: Module View,

Identification, Current, Power, Input Power, and Output Power.

D.5.9.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse cursor over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table, in the Alarm Browser, or in the RXT PM Table.

D.5.9.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.9.3 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 current levels.

Table D-300 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.9.4 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 power levels.

Table D-301 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.9.5 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power entering the receive transponder.

Table D-302 Field Descriptions for the Input Power Tab

Field Description

Input Power

D.5.9.6 Output Power Tab

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.10 Slot Properties???RXT-10G-N

The Slot Properties pane displays information about the directly modulated Receive Transponder???10 Gbps???Normal (RXT-10G-N) module that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

A block diagram is shown in the following figure.

Figure D-16 Cisco ONS 15800 or ONS 15801 Receive Transponder???10 Gbps???Normal

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

For the RXT-10G-N module, the Slot Properties pane displays the following tabs: Module View, Identification, Current, Power, Input Power, and Output Power. Fields on these tabs are described in the following sections.

D.5.10.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser or in the Equipment Inventory Table.

D.5.10.2 Identification Tab

D.5.10.3 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 current levels.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-305 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.10.4 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 power levels.

Table D-306 Field Descriptions for the Power Tab

Field Description

Laser 1 Current

D.5.10.5 Input Power Tab

D.5.10.6 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the receive transponder output power.

Table D-308 Field Descriptions for the Output Power Tab

Field Description

Output Power

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-308 Field Descriptions for the Output Power Tab (continued)

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.11 Slot Properties???RXT-10H-M

The Slot Properties pane displays information about the Receive Transponder???10 Gbps High Sensitivity???B1 Monitoring (RXT-10H-M) module that is installed in the slot selected in the NE Explorer tree. Use this properties pane to change the module performance monitoring thresholds.

A block diagram is shown in the following figure.

Figure D-17 Cisco ONS 15800 or ONS 15801 Receive Transponder???10 Gbps High Sensitivity???B1 Monitoring

For the RXT-10H-M module, the Slot Properties pane displays the following tabs: Module View, Quality of Service, Current, Power, Input Power, and Output Power. Fields on these tabs are described in the following sections.

D.5.11.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse cursor over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the B1 RXT PM Table.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.11.2 Identification Tab

D.5.11.3 Quality of Service Tab

Table D-310 Field Descriptions for the Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-310 Field Descriptions for the Quality of Service Tab (continued)

D.5.11.4 Current Tab

D.5.11.5 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 power levels.

Table D-312 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.11.6 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the receive transponder.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-313 Field Descriptions for the Input Power Tab

D.5.11.7 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the receive transponder output power.

Table D-314 Field Descriptions for the Output Power Tab

Field Description

Output Power

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.12 Slot Properties???RXT-B1

ONS 15800 and ONS 15801 receive transponder (RXT) modules are used in ONS 15800 and ONS 15801 terminal sites to retime, reshape, and regenerate low input demultiplexed signals.

A block diagram is shown in the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Figure D-18 Cisco ONS 15800 or ONS 15801 Receive Transponder???B1 Monitoring

RXTs shown on this sheet include:

???Receive Transponder???Directly Modulated???B1 Monitoring module (RXT-DM-M)

???Receive Transponder???Directly Modulated Long-Haul???B1 Monitoring module (RXT-DMLH-M)

For these RXT modules, the Slot Properties pane displays the following tabs: Module View,

Identification, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.12.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the B1 RXT PM Table.

D.5.12.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.12.3 Quality of Service Tab

Table D-316 Field Descriptions for the Quality of Service Tab

D.5.12.4 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 current levels.

Table D-317 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.12.5 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 power levels.

Table D-318 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.12.6 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the receive transponder.

Table D-319 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.12.7 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the receive transponder output power.

Table D-320 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.13 Slot Properties???RXT-FEC

Receive transponder-forward error correction (RXT-FEC) modules are used in ONS 15800 and ONS 15801 terminal sites to retime, reshape, and regenerate low input demultiplexed signals.

RXT modules shown on this sheet include:

???Receive Transponder???Directly Modulated???Forward Error Correction (RXT-DM-F) 2.5 Gbps module

???Receive Transponder???10 Gbps???Forward Error Correction (RXT-10G-F) module

For FEC RXT modules, the Slot Properties pane displays the following tabs: Module View,

Identification, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.13.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the FEC RXT PM Table.

D.5.13.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.13.4 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 current levels.

Table D-323 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.13.5 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the receive transponder Laser 1 power levels.

Table D-324 Field Descriptions for the Power Tab

Field Description

Laser Power

D.5.13.6 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the receive transponder.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-325 Field Descriptions for the Input Power Tab

D.5.13.7 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the receive transponder output power.

Table D-326 Field Descriptions for the Output Power Tab

Field Description

Output Power

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.14 Slot Properties???Transmitter Transponder

The transmitter transponder performs 3R regeneration of the 2.5 Gbps and 10 Gbps optical signal and provides client signal validation parameters. The module transposes input client signals to appropriate wavelengths and transmits them to the multiplexing section of the ONS 15808 system. Transmitter transponder modules add out-of-band forward error correction (OOB-FEC) signal encoding to the client signal to improve signal quality and transport distance.

A block diagram is shown in the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Figure D-19 Cisco ONS 15808 Transmitter Transponder

Transmitter transponders shown on this sheet include:

???Transmit Transponder???2.5 Gbps???C band???FEC Coding (TT-25G-Cxx)

???Transmit Transponder???10 Gbps???C band???FEC Coding (TT-10G-Cxx)

???Transmit Transponder???10 Gbps???C band???Single Slot???FEC Coding (TT-10G-SCxx)

???Transmit Transponder???10 Gbps???L band???Single Slot???FEC Coding (TT-10G-SLxx)

For ONS 15808 transmitter transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality Of Service, Current, Power, Input Power, Output Power, and Action.

D.5.14.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Equipment Inventory Table, in the Alarm Browser, or in the Transmitter Transponders PM Table.

D.5.14.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.14.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the transponder operating temperature.

Table D-328 Field Descriptions for the Temperature Tab

D.5.14.4 Quality of Service Tab

Table D-329 Field Descriptions for the Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-332 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.14.8 Output Power Tab

The Output Power tab allows you to assign thresholds and alarm severities for the transponder output power.

Table D-333 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

D.5.14.9 Action Tab

The Action tab allows you to force the ONS 15808 optical output power.

Table D-334 Field Descriptions for the Action Tab

FieldDescription

Output Power Setting

???The equalization of the channel downstream from the optical line, the optical channel S/N in fiber, and at the end of the optical line.

???The optical channel power at the end of the optical line.

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.15 Slot Properties???WCM

The Slot Properties pane displays information about the Cisco ONS 15800 or ONS 15801 slot that is selected in the NE Explorer tree. Use this properties pane to set performance monitoring thresholds for the module.

Wavelength Converter Modules (WCMs) are used at terminal (transmit direction) and optical add/drop multiplexing (OADM) sites to retime, reshape, and regenerate SONET and SDH signals.

A block diagram is shown in the following figure.

Figure D-20 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module

WCMs shown on this sheet include:

???Wavelength Converter Module???Externally Modulated???Normal (WCM-EM-Nxx)

???Wavelength Converter Module???622 Mbps???Normal (WCM-622-Nxx)

For WCM transponders, the Slot Properties pane displays the following tabs: Module View,

Identification, Temperature, Current, Power, Input Power, and Output Power.

D.5.15.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser or in the Equipment Inventory Table.

D.5.15.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.15.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the wavelength converter module laser temperature.

Table D-336 Field Descriptions for the Temperature Tab

Field Description

Laser 1 Temperature

D.5.15.4 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the wavelength converter module laser current levels.

Table D-337 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.15.5 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Table D-338 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.15.6 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the wavelength converter module.

Table D-339 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.15.7 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the wavelength converter module output power.

Table D-340 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.16 Slot Properties???WCM-10G-Nxx

The Slot Properties pane displays information about the module that is installed in the slot selected in the NE Explorer tree. Use this properties pane to set performance monitoring thresholds for the module. Wavelength converter modules (WCMs) are used at terminal (transmit direction) and optical add/drop multiplexing (OADM) sites to retime, reshape, and regenerate SONET and SDH signals.

A block diagram is shown in the following figure.

Figure D-21 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module???10 Gbps???Normal

For the Wavelength Converter Module???10 Gbps???Normal (WCM-10G-Nxx), the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Current, Power, Input Power, and Output Power.

D.5.16.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the LEM PM Table.

D.5.16.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.16.5 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Table D-344 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.16.6 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the wavelength converter module.

Table D-345 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.16.7 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the wavelength converter module output power.

Table D-346 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.17 Slot Properties???WCM-FEC

Forward error correction (FEC) wavelength converter modules (WCMs) are used at terminal (transmit direction) and optical add/drop multiplexing (OADM) sites to retime, reshape, and regenerate SONET and SDH signals.

A block diagram is shown in the following figure.

Figure D-22 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module???Forward Error Correction

WCMs shown on this sheet include:

???Wavelength Converter Module???Externally Modulated???Forward Error Correction (WCM-EM-Fxx)

???Wavelength Converter Module???10 Gbps???Forward Error Correction (WCM-10G-Fxx)

For FEC WCMs, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, Output Power, and Action.

D.5.17.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the FEC WCM PM Table.

D.5.17.2 Identification Tab

The Identification tab allows you to view and update wavelength converter module identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.17.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the wavelength converter module laser temperature.

Table D-348 Field Descriptions for the Temperature Tab

Field Description

Laser 1 Temperature

D.5.17.4 Quality of Service Tab

The Quality of Service tab allows you to assign thresholds and alarm severities for B1 and FEC counters. Click the 15 min radio button to assign thresholds for 15-minute collection increments. Click the 1 day radio button to assign thresholds for 24-hour collection increments.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-350 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.17.6 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Table D-351 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.17.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the wavelength converter module.

Table D-352 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.17.8 Output Power Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-353 Field Descriptions for the Output Power Tab (continued)

D.5.17.9 Action Tab

???the equalization of the channel downstream from the optical line, the optical channel S/N in fiber, and at the end of the optical line.

???the optical channel power at the end of the optical line.

Click Execute to apply your changes to the setting. Click Update to retrieve the current setting from the NE.

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.18 Slot Properties???WCM-EM-Fxx

A block diagram is shown in the following figure.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Figure D-23 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module???Externally

Modulated???Forward Error Correction

For Wavelength Converter Modules???Externally Modulated???Forward Error Correction (WCM-EM-Fxx), the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, Output Power, and Action.

D.5.18.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the FEC WCM PM Table.

D.5.18.2 Identification Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.18.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the wavelength converter module laser temperature.

Table D-356 Field Descriptions for the Temperature Tab

Field Description

Laser 1 Temperature

D.5.18.4 Quality of Service Tab

Table D-357 Field Descriptions for the Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.18.5 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the wavelength converter module laser current levels.

Table D-358 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.18.6 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-359 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.18.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the wavelength converter module.

Table D-360 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.18.8 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the wavelength converter module output power.

Table D-361 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

D.5.18.9 Action Tab

The Action tab allows you to specify the output power setting.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

???The equalization of the channel downstream from the optical line, the optical channel S/N in fiber, and at the end of the optical line.

???The optical channel power at the end of the optical line.

Click Update to retrieve the current setting from the NE.

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

D.5.19 Slot Properties???WCM-EM-Mxx

The Slot Properties pane displays information about the 2.5-Gbps Wavelength Converter Module???Externally Modulated???B1 Monitoring (WCM-EM-Mxx) that is installed in the slot selected in the NE Explorer tree. Use this properties pane to set performance monitoring thresholds for the module.

Wavelength converter modules (WCMs) are used at terminal (transmit direction) and optical add/drop multiplexing (OADM) sites to retime, reshape, and regenerate SONET and SDH signals.

A block diagram is shown in the following figure.

Figure D-24 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module???2.5 Gbps???B1

Monitoring

For 2.5-Gbps, B1-monitoring WCM modules, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, and Output Power.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.19.1 Module View Tab

The Module View tab displays a graphic of the module that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the B1 LEM PM Table.

D.5.19.2 Identification Tab

D.5.19.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the module laser temperature.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-364 Field Descriptions for the Temperature Tab

Field Description

Laser 1 Temperature

D.5.19.4 Quality of Service Tab

The Quality of Service tab allows you to assign high alarm thresholds and severities for B1 counters. Click the 15 min radio button to assign thresholds for 15-minute collection increments. Click the 1 day radio button to assign thresholds for 24-hour collection increments.

Table D-365 Field Descriptions for the Quality of Service Tab

D.5.19.5 Current Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.19.6 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Table D-367 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

D.5.19.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the module.

Table D-368 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.19.8 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the module output power.

Table D-369 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.20 Slot Properties???WCM10

Wavelength converter modules (WCMs) are used at terminal (transmit direction) and optical add/drop multiplexing (OADM) sites to retime, reshape, and regenerate SONET and SDH signals.

A block diagram is shown in the following figure.

Figure D-25 Cisco ONS 15800 or ONS 15801 Wavelength Converter Module???10 Gbps???B1

Monitoring

WCMs shown on this sheet include:

???Wavelength Converter Module???10 Gbps???B1 Monitoring (WCM-10G-Mxx)

???Wavelength Converter Module???10 Gbps High Output Power???B1 Monitoring (WCM-10H-Mxx)

For these transponders, the Slot Properties pane displays the following tabs: Module View, Identification, Temperature, Quality of Service, Current, Power, Input Power, and Output Power.

D.5.20.1 Module View Tab

The Module View tab displays a graphic of the transponder that is installed in the slot. The number of critical, major, minor, and warning alarms for the module is displayed under Alarm Status. (Moving the mouse pointer over the graphic also displays the alarm counts.) The module status is displayed under Operational State. Right-clicking the graphic opens a shortcut menu that you can use to display the module in the Alarm Browser, in the Equipment Inventory Table, or in the B1 LEM PM Table.

D.5.20.2 Identification Tab

The Identification tab allows you to view and update wavelength converter module identification information.

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.20.3 Temperature Tab

The Temperature tab allows you to assign performance monitoring thresholds for the wavelength converter module laser temperature.

Table D-371 Field Descriptions for the Temperature Tab

Field Description

Laser 1 Temperature

D.5.20.4 Quality of Service Tab

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

Table D-372 Field Descriptions for the Quality of Service Tab

D.5.20.5 Current Tab

The Current tab allows you to assign performance monitoring thresholds for the wavelength converter module laser current levels.

Table D-373 Field Descriptions for the Current Tab

Field Description

Laser 1 Current

D.5.20.6 Power Tab

The Power tab allows you to assign performance monitoring thresholds for the wavelength converter module Laser 1 power levels.

Table D-374 Field Descriptions for the Power Tab

Field Description

Laser 1 Power

Appendix D Slot Property Information???FC_MR-4, FMEC, Multirate, Optical, and Transponder Cards

Transponder Cards

D.5.20.7 Input Power Tab

The Input Power tab allows you to assign performance monitoring thresholds for the power coming into the wavelength converter module.

Table D-375 Field Descriptions for the Input Power Tab

Field Description

Input Power 1

D.5.20.8 Output Power Tab

The Output Power tab allows you to assign performance monitoring thresholds for the wavelength converter module output power.

Table D-376 Field Descriptions for the Output Power Tab

Field Description

Output Power 1

Note See Table 1-20 on page 1-44 for descriptions of actions that can be performed using the buttons at the bottom of the window.