Boss_Audio_Systems_Car_Stereo_System

INSTRUCTIONS

CONTENTS

Panel Introduction

Basic Functions

Remote Control Function

Turn the Unit On/Off

Enter into the Main Interface

Play SD card/USB memory device

Radio Function Operation

Disc Function Operation

Play/Eject Disc

DVD/VCD Disc Playback

CD Disc Playback

MP3/WMA Format Disc Playback

Touch Menu Function

Bluetooth Function Operation

iPod function operation

External input operation

Other Function Operations

Rear view function

General setting

Time setting

Language Setup

Video Setup

Audio setting

Steering Wheel Setup

Touch calibration

Wiring Diagram

Trouble shooting

Specifications

Accessory

DVD Parental control function

INSTRUCTIONS

DVD Parental control function

DVD Parental control function???The default set for DVD is #8 adult, which means all grades of DVD can be read without entering password.To change the default grade,you need to follow the below procedure: Press SETUP button on the remote, display will show the system set up menu

and the submenu,select password and enter

0000, you will be able to choose the DVD grade as default.

INSTRUCTIONS

BASIC FUNCTION

Bluetooth

iPod

6. SEEK Knob/( / )/ (SEEK+/SEEK-)/(SEEK/SEEK)(Speed forward/backward/Select station/song)

In radio mode, press/rotate the knob to select station upward/backward. Long press/rotate the knob to

automatically scan station.

In playback mode, short press/rotate the knob to select song upward/backward,long press/rotate it to

achieve speed forward/backward function.

7 Dual (front and rear)USB

Warning :You can only use either front or rear USB at a time.Never connect both front and rear USB at the same time! This could cause malfunctions.

9.MIC Input

Bluetooth MIC input.

INSTRUCTIONS

WIRING DIAGRAM

This player is equipped with ISO standard connector, please follow below instruction:

TROUBLE SHOOTING

INSTRUCTIONS

REMOTE CONTROL FUNCTION

CLASSIC

5.SEEK+ ( )/ SEEK- ( )button

In normal playback MP3, USB, SD songs,

press this button to previous song or next

song.

28 DSP

INSTRUCTIONS

Audio setting

Click icon on setup interface to access audio setting interface, as shown in right(PIC 1) diagram:

You can turn on or turn off the existing functions on audio setting interface.

II.Connect anode and cathode of direction control wire of the car with anode and cathode of direction control wire of this device, and press the buttons on steering wheel one by one and record the corresponding sequence and functions.

III.Click the button of steering wheel needs to be allotted so as to select the corresponding setting function, such as volume +.

IIII. Buttons on steering wheel shall display the corresponding functions, such as volume + . To modify function settings, repeat procedures 3~4.

To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat procedures 3~4 for resetting.

Touch calibration

If touch calibration error occurs, you can adjust the touch coordinate by ???Touch calibration???.

Click icon on setup interface, input password [888888] to confirm to access touch calibration interface, as shown in below diagram:

Touching methods

Use touch pen to click the center of ???+??? icon, and move along with center of ???+??? icon so as to calibrate the screen. It shall automatically save data and exit after screen calibration. Please accurately click all positions on screen, or the accuracy of touch calibration shall be affected.

INSTRUCTIONS

Access setup interface

Click [Setup] icon on main interface to access setup interface.

General setting

Click icon on setup interface to access general setting interface, as shown in below PIC 1 diagram:

In general setting interface, you can select to turn on or turn off the existing functions. You can set wallpaper and opening picture you like and check version number of DV/DC, click icon to browse up/down.

Wallpaper selection

Click icon on wallpaper bar , direction icon shall pop up, click it to select wallpaper.

Opening picture

Click icon on opening picture bar , direction icon shall pop up, click it to select opening picture.

Time setting

Click icon on setup interface to access time setting interface, as shown in below PIC 2diagram:

Click icon on time bar time setting interface shall display, as shown in below PIC 3 diagram:

Click icon beside hour and minute to separately set hour and minute.

Language Setup

During use, you can select your familiar language to display menu by language setup. Click icon on setup interface to access language setting interface, as shown in right (PIC 4) diagram:

Click the corresponding icon on the language bar desired to be set so as to switch the language type, when there are more than 3 languages, direction icon shall pop up, click it to select your familiar language.

Video setting

Click icon on setup interface to access video setting interface, as shown in right (PIC 5) diagram:

At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.

INSTRUCTIONS

28.DSP

Press this button to show the time.

21.UP, DOWN, LEFT, RIGHT, ENTER button

When playing MP3, USB, SD returns to song menu, up, down selections can be up / "" button or down / "" key to select up and down, select and press "" key to confirm. The selected tracks can be played. Press the left or right arrow keys to "" or "" key, can be on the next page function operation.

INSTRUCTIONS

Turn on/off Host

When the ignition switch is put in ACC or ON position,Press[ ] button on the front panel to turn on the unit.After the host starts, hold []button for 3 seconds , the host will turn off.

Access main interface

In the other mode, click on the interface to return the icon will switch to the main interface.

INSTRUCTIONS

iPod function operation

Connect to iPod first, touch [iPod] icon on main interface to access iPod interface, as shown in below diagram.

Touch the function icons so as to access the corresponding function operations.

USB/SD Card function operation

StopPrevious Song/next Song

External input operation

Back to the

main interface

When there is a USB device/SD card connected, the unit can conduct the playback of audio/video/ image files in the USB device/SD card.

Insert/Eject USB storage device

1.Connect a USB recorded with media information to the unit by a USB connecting cable.

2.When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.

Insert/eject SD card

1.Insert a SD card recorded with media information into the SD card slot in the unit correctly until it is locked.

2.When pulling out the SD card, exit SD card playing state first, then press the SD card and it shall pop up after unlocking.

Enter/exit

Insert a USB storage device or SD card to automatically play data contained in it. If the unit has connected with a USB device or SD card, touch[ USB ]icon in the main interface to enter into the external storage playback interface; Touch[ SD ]icon to enter into the SD card playback interface. During playback, touch the top center area of the screen to pop up the touch menu, operate touch menu to perform various playback controls.

Play

After SD card/USB removable device being read out, the operation methods are similar to disk operation methods.

Connect the video input plug with external video input jack, and connect the audio input plug with external audio input jack.

Touch [Input] icon on main interface to access external input interface.

Audio You can adjust thevolume, bass, pitch for input audio.

You can adjust the speaker volume by adjusting the front and back,left and right column.

Video You can adjust the brightness, contrast, saturation and hue for input video. You can also choose the video standard mode.

NO VIDEO SIGNAL

Other functions

Rearview function

In any running state, the video signal can switch to reverse video state when reversing the car, and the system shall return to its initial running state after reversing the car.

Warning

Do not rely on CCD system completely, please make sure you use direct eyesight while driving.Back rearview system only assists in driving. As the distance range of rearview system is limited, completely relying on the rearview system during driving may cause accidents.

INSTRUCTIONS

Bluetooth Function Operation

Enter/exit

Touch [ Bluetooth ] icon in the main interface to enter the bluetooth interface. Touch icon to exit bluetooth interface.

Pair/link

To use Bluetooth hand-free function, make connection first, i.e. match the host with the Bluetooth mobile phone.

Operation methods:

Set the host to be matching state, and open the Bluetooth of your mobile phone and use the mobile phone to search device, the mobile phone shall prompt to match password with the Bluetooth when it has searched the Bluetooth device.

Input Bluetooth password (0000) to the mobile phone and confirm. The mobile phone shall prompt whether authorize to this device,please select [Yes]. Phone and Bluetooth shall automatically connect within 20 seconds. Under any working mode, the host shall convert to Bluetooth state if there is an incoming call. And the host shall restore to current mode after hanging up.

When the Bluetooth device matches with this device, the connection status shall display ???Connected???, otherwise, it shall display ???No connection???.

Dialing

You can dial on mobile phone directly or input phone number through the number buttons on the screen, click to delete if there is input error.

After input the phone number, click to make a call, and click to hang up the phone. Click during a call so as to switch the voice between car speaker and mobile phone.

Call records

Click to access call records interface as below PIC 2:

Received calls: Touch this button to check all the phone numbers of received calls.

Dialed numbers: Touch this button to check all the dialed phone numbers.

Missed calls: Touch this button to check all the phone numbers of missed calls.

Bluetooth volume

Click to access Bluetooth volume interface as below PIC 3:

INSTRUCTIONS

Radio Function Operation

Enter/exit

Touch [ RADIO ] icon in the main interface to enter into the radio interface.

Touch icon to return to main interface, and then touch other function icons so as to exit radio mode.

Band selection

Click [BND] icon so as to switch among FM1,FM2, FM3,AM1, AM2 bands.

Search/Save radio stations

Short press [Scan] icon to browse the stored radio stations.

FM band can save 18 radio stations (Six stations for FM1/FM2/FM3), AM band can save 12 radio stations (Six stations for AM1/AM2).

Scan radio

Short press icon to manually fine-tune radio stations upward/downward. Long press icon to automatically search and save radio stations.

Sound setting

Click [EQ] icon can switch to different sound mode.

Mute on/off

Click [Mute] icon to turn on/off mute function

TFT on/off

Click icon to turn off TFT, and then click the screen area so as to turn on TFT. Click icon so as to slide screen angle.

previous song

next song

PIC 3

INSTRUCTIONS

Disc Function Operation

Play/eject disc

Play disc

Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play.

Eject disc

(1)Click button on the panel to eject the disc.

(2)If a disc has not been took away 15 seconds after it is ejected, system will automatically take in the disc but not play.

Do not insert two discs or more.

DVD/VCD disc playback

During playback of disc, touch the middle lower area of the screen to pop up the touch menu, operate the touch menu to perform various playback controls.(PIC 1)

CD Disc Playback

After a CD is inserted, system shall access disc reading state immediately.

When there is a disc in the device, click [Disc] at the main interface so as to access disc reading state.

After the disc being read out, system shall automatically play in sequence.

MP3/JPEG/MPEG4 disk playing

When the disc contains readable files, such as MP3/JPEG/MPEG4 files, it shall be automatically read out and played after slipping into DVD player.

During playing, touch the screen area and the touch menu shall pop up. Operate the touch menu for various playing.

Touch Menu Function Description

Play/pause

Touch the button to pause, retouch it to continue to play. Stop

Touch the button to enter into prestop status. Fast forward/backward

Consecutively touch this button to select the speed of fast-forward/fast-backward.

PIC 1

INSTRUCTIONS

Access next menu

Touch it to access the next menu interface.

Time setting

Touch this button to access time setting interface.

Stereo on/off

Touch it so as to turn on/off stereo.

Return to root menu

Touch this icon, it shall return to root menu of disk in DVD state and access PBC menu playing in VCD state. All chapters in the disk shall be displayed on the interface, touch the chapter icon directly for playing.

Access title menu