TC9217MM-W, TC9220MM-W, TC9227MM-W

Instruction Manual

EN Monitor Mounts

MONITOR MOUNT COMPATIBILITY CHART

For Bosch LTC Series Monitors

Installation Hint for TC9217MM, TC9220MM, and TC9227MM Series Monitor Mounts, RE: Step 4.

For proper center of gravity alignment of Bosch monitors on the bottom support tray, a recommended starting point is to use the third (3rd) square hole from the front edge of the tray to mount the vertical support arm using pin E.

SERVICE

If the unit needs servicing, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions.

Service Centers

USA

For additional information, see www.boschsecurity.com.

Bosch Security Systems | February 3, 2005

TC9227MM-W 27"

Each monitor mount is for use with a single TV or monitor of a specified size only.

Place TV onto a piece of pipe as

shown. (Pipe should be a few inches wider than the TV.) Roll TV back and forth to find the balance point. This is the center of gravity. Mark the center of gravity on the side of the TV.

Attach support tray (A)

to vertical support arms

(P) as shown.

Note: Choose the square hole which aligns closest with the center of gravity mark on the TV (as determined in step 1). Attach anti-rollout hooks (R) as shown using M6 screws (Z) and retainer bars (Y). Note: Extruded side of retainer bar (Y) goes towards anti-rollout hook (R).

Hand tighten only.

F

G

H

I

For Wood Stud Walls drill three 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm) into stud center. Attach wall arm (W) using three #14 x 2.5" (6 mm x 65 mm) wood screws (V).

WARNING

???Tighten wood screws so wall arm is firmly attached, but do not tighten with excessive force! Overtightening can cause stress damage to wood screws, greatly reducing their holding power. Tighten to 80 in ??? lb (9 N.M.) maxi- mum torque.

WOOD

STUD

WALL

W

V

WARNING

???When installing BOSCH wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica- tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

???Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

???Make sure that the wall will safely support four times the combined load of the equipment and all attached hard- ware and components.

For Concrete Walls use wall arm (W), making sure that it is level, as a template to mark holes. Drill 1/ 4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert concrete anchors in holes flush with wall as shown (right). Place wall arm (W) over anchors and secure with #14 x 2.5" (6 mm x 65 mm) wood screws (V). Tighten all fasteners.

WARNING

???Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

???Never tighten in excess of 80 in ??? lb (9 N.M.).

???Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended.

WARNING

???Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer.

CONCRETE

WALL

W

V

Note: Slots in corners of top clamps (Q) and corners of vertical support arms (P) allow for the installation of safety belt (model ACC 666, sold separately). If using this belt, install it now.

Position TV onto support tray (A). Position anti-rollout hooks (R) against front edge of TV.

WARNING

???Each anti-rollout hook (R) should have at least 1/4??? of surface contact with the front of the TV. If this is not the case the support tray (A) must be adjusted smaller [see step 2], or the vertical support arms (P) adjusted inward [see step 4].

Insert top clamps (Q). Note: Top clamps (Q) fit between rollout protectors (R) and vertical support arms (P) [DETAIL 1]. Press down on each top clamp (Q) while securely tightening each M6 screw (Z).

By hand, thread one serrated flange head screw (K) into each vertical support arm (P) into one of three threaded holes [1, 2, or 3; DETAIL 2]. Choose the threaded hole that will allow just enough tilt clearance [see step 9]. Leave about 1/4" of exposed thread.

T

(BOTTOM VIEW)

S

When attaching the horizontal support (S) to wall arm or ceiling plate, carefully thread retaining collar (O) onto end of flush mount (T) tube (or extension column). Tighten at least four complete turns ending with one of the small threaded holes aligned with slot in the end of flush mount tube (T) (or extension column). Insert and tighten one M5 screw (F).

WARNING

???Set screw (F) is self tapping and may be hard to get started but is essential to this installation. Failure to install this screw can cause the mount to fall.

Adjust TV to desired tilt then tighten screws. Maximum tilt is 30??. If tilt clearance is a problem revisit step 7, DETAIL 2.

WARNING

??? Tighten all screws securely.

Note: Parts may appear slightly different than illustrated.

GENERAL WALLMOUNTKITSPECIFICATIONS

(686 mm) (889 mm)

300 lb

300 lb

(889 mm) (1067 mm)

???Weight of TV or monitor not to exceed Max. Load Capacity (BOSCH rating)!

R

300 tilt range

wall

TV

support tray

D

?? 2005 Bosch Security Systems GmbH

3935 890 28113 05-05 | February 3, 2005 | Data subject to change without notice.