BABY BASSINET ???N CRADLE
WITH TOYBOX BASE
MODEL NUMBERS:
Assembly
Instructions.
Adult Assembly
Required.
Save these instructions for future use.
Visit us online at www.badgerbasket.com
Mail: PO Box 227, Edgar, WI
BABY BASSINET ???N CRADLE
WITH TOYBOX BASE
MODEL NUMBERS:
Assembly
Instructions.
Adult Assembly
Required.
Save these instructions for future use.
Visit us online at www.badgerbasket.com
Mail: PO Box 227, Edgar, WI
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware. If anything is missing or not satisfactory, please DO NOT call the store where purchased or return the product to them.
Contact Badger Basket for assistance.
Most problems are resolved without you needing to leave home. When contacting us, please have this instruction manual, your product model number, and your product version code ready. For fastest service, go to http://www.badgerbasket.com/parts
Your Product Version Code is: 3.0/1108/TG
WARNING - FAILURE TO FOLLOW THESE WARNINGS
AND THE INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY OR DEATH:
FALL HAZARD: To help prevent falls, please note this bassinet is a safe place for your newborn to sleep until Baby is 4 months old, 20 lbs. (9.09 kg), OR when Baby can push up, roll over, or crawl - whichever limit comes first.
???SUFFOCATION HAZARD - Infants can suffocate:
??in gaps between an extra pad and the side of the bassinet,
??on soft bedding.
NEVER add a mattress, pillow, comforter, or padding. Use ONLY the pad
and/or bedding provided by the manufacturer. If a sheet is used with the pad, use only the one provided with the bassinet or one that is from Badger Basket Company or one that is specifically designed to fit the dimension of the the mattress provided.
???TO REDUCE THE RISK OF SIDS: pediatricians recommend that healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
???DO NOT move or carry the bassinet with your baby inside of it.
???DO NOT allow other children or pets to climb into or onto the bassinet when your infant is inside.
???DO NOT attach or place toys with strings in or around the basket. Strings can cause strangulation or choking.
???Keep bassinet away from stoves, heaters, camp fires/flames, fireplaces, stairs, open windows, window blinds, running or standing water, and any other hazard which could cause injury to your baby.
???NEVER use plastic bags inside the basket such as to cover the mattress.
???Bassinet should always be placed on a firm, flat surface. It should never be placed near stairs or on tables or elevated surfaces.
???READ ALL INSTRUCTIONS before use of this product. Keep instructions for future use. Product and/or hardware may include small parts or screws with sharp points.
???Choking Hazard! Keep unassembled parts out of the reach of small children. Use only the parts and hardware provided by Badger Basket.
???Do not use the bassinet if it is damaged or broken.
???Periodically check to make sure all the bolts and screws remain tight.
PARTS & HARDWARE:
C
D
E
AF G
AB
L
USE AND CARE INSTRUCTIONS:
Wipe the wood/MDF parts clean with a damp cloth and mild soap as needed. Spot clean basket as needed. Bedding Set can be machine washed on cold, gentle cycle; tumble dry low or no heat.
STEP 1: See PICTURE 1. Take ONE END PANEL (A) and attach the FOUR RAILS (B) using FOUR BOLTS
(C).
Attach the rails to the INSIDE FACE of the END PANEL. The inside face has countersunk areas for the rails and slots that you will use later for the mesh basket.
Position the bottom rails with the grooves facing up; and position the top rails with the grooves facing down.
Slip the TWO NYLON SNAP STRAPS (D) over the TOP RAILS (B). Position them so that they are ready to snap to the snaps on the bassinet body (H).
STEP 2: See PICTURE 2. Attach the second END PANEL (A) to the FOUR RAILS (B) using FOUR BOLTS
(C).
STEP 3: See PICTURES 3A and 3B. Turn the bassinet stand upside down.
Insert the TWO DOWELS (E) through the edge pockets of the MESH BASKET (F). Insert the ends of the ONE DOWEL (E) into the SLOTS cut into the inside faces of the END PANELS (A). Stretch the mesh basket over the rails and around to the other side, and insert the second wood dowel into the dowel slots. Adjust the mesh basket to remove wrinkles.
Attach the FOUR CASTER WHEELS (G) to the corners of the end panels using one BOLT and one KNOB for each WHEEL. The knobs go on the inside.
B
B
B
PICTURE 2
A
STEP 4: See PICTURES 4A and 4B. Turn the bassinet stand over.
Fit the slots on the BASSINET BODY (H) over the raised edge pieces on the top of the END PANELS (A). See PICTURE 4A.
Next, snap the NYLON SNAP STRAPS (D) onto the snaps on the bottom edge of the BASSINET BODY
(H). See PICTURE 4B.
PICTURE 3A
STEP 5: Unpack the BEDDING SET (I). You may launder the set be- fore use if you wish, and/or iron, press, or steam it to remove wrinkles. Machine wash cold, gentle cycle only; air dry or tumble dry low or no heat. Iron on lowest setting for poly/ cotton.
Locate the buttonholes on the FABRIC LINER and slip them over the spools on the BASSI- NET BODY (H). Smooth the liner around the sides and bottom in-
side the bassinet, and adjust it around the outside of the bassinet. Put the SHEET onto the MATTRESS PAD (J) and place
the mattress pad into the bassinet.
Snap together the HOOD HOOP FRAME (K) as shown in PICTURE 5. Stretch the fabric HOOD over the FRAME and slip the elastic loops over the ends of the frame to hold the hood in place. Snap the FRAME (K) onto the spools on the BASSI- NET BODY (H).
The bassinet is now ready for your baby! See PICTURE 6.
PICTURE 6
NOTE: Your bassinet bedding may vary from shown
???Puzzle Piece??? Fit
PICTURE 4A
Snap Straps
PICTURE 4B
Raised Lip towards front
PICTURE 5
PICTURE 7
To use the bassinet as a Rocking Cradle, loosen the caster knobs, rotate the casters into the up position, and retighten the knobs. See PICTURE 7.
TO CONVERT THE STAND TO A TOY BOX
PICTURE 8
STEPA: Remove the bedding, bassinet body, hood, wooden dowels, and mesh basket, and set them aside.
STEP B: Unscrew and remove all four of the bolts holding the TOP RAILS and set aside the screws, rails, and nylon snap straps.
STEP C: Insert the two larger SIDE PAN- ELS (L) into the grooves on the bottom rails with the white sides facing out.
STEP D: