INTRODUCTION

Thank you for choosing the PAV2000DTV MOBILE THEATER AM/FM, with DVD/CD Changer Controller and Motorized 7??? Wide TFT LCD Display. This unit provides state of the art electronics and is constructed to provide years of reliable, trouble-free service. Please read all documentation prior to using this product. The documentation will assist you in obtaining the best equipment performance. Save this manual for later use.

IMPORTANT NOTICE

For your safety, the driver should not watch the TV or operate the controls while driving. Please note watching and/or operating the TV while driving is prohibited by law in some countries. An LCD Panel and/or Video Monitor may be installed in a motor vehicle and visible to the driver if the LCD Panel or Video Monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD Panel or Video Monitor is used for television reception, Video or DVD playback, then the LCD Panel or Video Monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle???s parking brake is applied. Always keep the volume to a level at which outside sounds can be heard.

SAFETY PRECAUTION

For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. Enjoy your entertainment system but always remember-safety of all passengers remains the number one priority.

1

CAUTIONS AND WARNINGS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated ???Dangerous Voltage??? within the product???s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CLASS 1

LASER PRODUCT

CLASS 1

LASER PRODUCT

The label above is attached to the chassis / case and notes that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

2

IMPORTANT SAFETY INSTRUCTIONS

Safety Precautions

1. Caution

Do not spill or spray liquid of any kind on or in the system (this may result in a fire or electric shock). Insert the unit all the way in until it is fully locked in place. Otherwise, it may fall out of place when jolted. To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. To prevent damage to the motorized mechanism do not hold the LCD display panel while it is opening or closing. Do not drop the PAV2000DTV or subject it to strong shocks. Doing so could damage the delicate parts contained within the unit. Use the hardware supplied with the PAV2000DTV for the installation. The use of incorrect hardware can damage the unit.

2. Warning

During installation of the PAV2000DTV, make sure to use automotive-grade wires or other wires with a 0.75mm?? (AWG18) or more when extending the ignition, battery, or ground wire to prevent wire deterioration and damage to the wire coating. Ensure that the unit is grounded to a negative 12VDC power supply.

To reduce the risk of electric shock, do not perform any servicing other than that contained within the operating instructions. There are no user-serviceable parts inside. Refer all servicing to qualified service personnel. Do not install the PAV2000DTV in an area that is exposed to direct sunlight, excessive heat humidity and/or dusty conditions. Do not install the PAV2000DTV where it may be exposed to water splashing or the possibility of rain. Only replace fuses with fuses of the same ampere rating. Failure to do so may result in damage to the unit, use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. In order to prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

Do not use 3-inch CD???s. Do not use adapters to load 3-inch CDs in the CD slot. It is possible for the 3-inch CD to separate from its adapter and damage the unit.

5. Cleaning DVD Player

When cleaning, make sure the system is unplugged from the power source. Do not use liquid cleaners or aerosol cleaners. Use a soft cloth lightly dampened with water for cleaning the exterior of the system only.

6. Disc

It is not recommended to insert 3??? CD???s with adapters into the PAV2000DTV. The CD adapter may separate from the CD and damage the unit. Do not use irregularly shaped discs such as heart or star-shaped discs as they may cause the DVD Player to malfunction. Do not stick paper, tape or glue on the disc. Do not expose the disc to direct sunlight or heat sources. Do not touch the surface of disc, handle the disc by its

3

edge. Always wipe the disc from the center out with a soft cleaning cloth when cleaning the disc. Remove the disc from the DVD Player and store it in its case after playing.

NOTE: Some software producers may intentionally fix some playback operations of discs. Since this DVD Player plays discs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the discs.

4

5

PAV2000DTV SYSTEM SPECIFICATIONS

FM Tuner Specifications

8

LCD Monitor Specifications

NOTE

Specifications and design are subject to be changed without notice for further improvement.

NOTE

If you experience problems during installation, consult your Audiovox dealer.

If the unit fails to operate properly, press the Reset button. The unit returns to factory setting when the Reset button is pressed. If the unit still fails to operate properly after the Reset button has been pressed, contact your local Audiovox dealer for assistance.

9

INSTALLATION OF THE PAV2000DTV SYSTEM

Installation Kit(s) Contents

Headunit Installation

Choose the mounting location carefully so that the unit will not interfere with the normal driving function of the driver. Avoid installing the unit where it would be subject to high temperatures such as from direct sunlight or hot air from the heater or where it would be subject to dust, dirt or excessive vibration. Use only the supplied mounting hardware for a safe and secure installation.

Mounting Angle Adjustment

Adjust the mounting angle to less than 20 degrees.

MOUNTING EXAMPLE

Installation in the dashboard

10

STRAP

Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle.

Installing the Holder

After inserting the holder into the dashboard, select the appropriate tabs according to the thickness of the dashboard material and bend them inwards to secure the holder in place.

HOW TO DETACH THE MOUNTING FRAME

1.Insert the release keys into the holes indicated by ???A???.

2.Remove the frame ???B??? from the unit.

NOTE:

Keep the release keys in the safe place, as you may need it in the future to remove the unit from the car.

11

Installation of the RT Box

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction, for example, the source may skip.

1.Align the holes in the unit with the vehicle-mounting bracket and secure the unit with the accessory screws.

2.During installation, do not use any screw except for those provided. The use of different screws might result in damage to the main unit.

NOTE: Damage may occur if a screwdriver or similar tool is used with excessive force during the installation.

12

Connecting to Power & Multi Channel AV Control Unit System

Power Connection to Head Unit

The illustration shown below depicts a typical power connection though the actual connection may vary depending on manufacturers (refer to the documentation supplied with the equipment to be connected). If the connection is not properly made, the unit may sustain unexpected damage.

1.Connect the Red wire (1) to ACC Power.

2.Connect the Yellow wire (2) to the Battery (+).

3.Connect the Orange/White wire (3), to the Dash Light wire.

NOTE: If the Orange/White wire is not connected to the head unit???s front panel will not be illuminated.

4.Connect the Blue/White wire (4) to an Optional Power Amplifier power control terminal.

5.Connect the vehicles Antenna Power wire (motorized or film-type) to head unit???s Blue Auto Antenna wire (5).

6.Connect the Orange wire (6) to the Optional Backup Camera.

7.Connect the Pink wire (7) to the Optional Telephone Mute wire.

8.Connect the Brown wire (8) to the Parking Brake.

NOTE: If the Brown wire is not connected to the Parking Brake, video will not be displayed on the screen.

9.Connect the Black wire (10) to Ground.

13

RT Box Connections

1.Connect the Yellow wire to the Battery (+).

2.Connect the Red wire to ACC Power.

3.Connect the Black wire to Ground.

WIRING DIAGRAM OF RT BOX 16PIN CONNECTOR

1.Connect the Yellow wire (1,9) to the Battery (+).

2.Connect the Black wire (2) to Ground.

3.Connect the Red wire (3) to ACC Power.

4.Connect the White wire (4) to the Positive (+) of the Left Front Speaker.

5.Connect the White/Black wire (5) to the Negative (-) of the Left Front Speaker.

6.Connect the Gray wire (6) to the Positive (+) of the Right Front Speaker.

7.Connect the Gray/Black wire (7) to the Negative (-) of the Right Front Speaker.

14

8.Connect the Brown wire (8) to the Positive (+) of the Center Speaker.

9.Connect the Blue/Black wire (10) to the Negative (-) of the Navigation Sound

10.Connect the Blue wire (11) to the Positive (+) of the Navigation Sound

11.Connect the Green/Black wire (12) to the Negative (-) of the Left Rear Speaker.

12.Connect the Green wire (13) to the Positive (+) of the Left Rear Speaker.

13.Connect the Purple/Black wire (14) to the Negative (-) of the Right Rear Speaker.

14.Connect the Purple wire (15) to the Positive (+) of the Right Rear Speaker.

15.Connect the Brown/Black wire (16) to the Negative (-) of the Center Speaker.

Connecting to the Multi Channel AV Control Unit System

The Illustration on the following page is an example setup with the Multi Channel AV Control Unit System. The exact connection method will vary depending on the specific components selected for a particular installation. Please refer to the owner???s and installation manuals supplied with the associated equipment.

15

???When installing a Subwoofer, use an additional power amplifier equipped with a Subwoofer analog line out.

WARNING

The Digital Audio Output of this DVD player can only be connected to a compatible Dolby Digital and/or DTS decoder or to an amplifier equipped with a digital audio input.

High volume digital signals may damage other equipment and hearing.

Connecting to the DVD Changer Control System

Connecting to the Multi Channel AV Control Unit System w/ Additional 6CH Amp

The Illustration on the following page is a possible example for Multi Channel AV Control Unit System in additional 6CH Amplifier with RT BOX. The exact connection method will vary depending on the specific components selected for a particular installation. Please refer to the owner???s and installation manuals supplied with the associated equipment.

17

FRONT PANEL MAINTENANCE

Lens Fogging

In certain weather conditions, dew or condensation may form on the lens in the player. In this condition, it may be possible that the discs will not play. If this happens, remove the disc and wait for the condensation to evaporate. If the unit does not operate normally after a while, consult your Audiovox dealer.

Cleaning the Unit

If it becomes necessary to clean the front panel of the unit, use a clean dry soft cloth wipe it clean. If the front panel is still dirty after using the dry cloth, moisten the cloth with a neutral cleaner, and then wipe it with a dry cloth to remove all of the cleaner.

Do not apply spray cleaner directly onto the unit. Do not wipe the front panel with a hard cloth or using a volatile liquid such as thinner or alcohol, which may scratch the surface or erase characters.

Cleaning the CD Slot

The CD slot should be clean and clear of any dust build-up. Discs may become scratched due to dust accumulation. Use a clean dry cotton swab to remove any dust build-up

19

HANDLING CDs

Do not touch the recorded surface of the CD.

CD-R and CD-RW discs are easier to damage than a normal music CD.

Do not apply tape or adhesive stickers etc. to the CD. Tape or adhesive stickers could come off and cause damage to the unit.

CD cleaning

Clean discs from the center of the disc and move outward towards the outside edges.

Removing CDs

When removing CDs from the unit, pull the discs out horizontally.

CDs That Can Not Be Used

CDs that are not round cannot be used.

Do not use CDs that are scratched or dirty.

This unit can only play discs of the following formats:

???Audio CD

???CD-R

???CD-RW

???DVD

The unit may not correctly play discs with other formats.

20

CD-R or CD-RW discs that have not been finalized cannot be played. (For the finalization process, refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.)

CD storage

Do not place CDs in direct sunlight (On the seat or dashboard etc.) or where the CDs will be subjected to high temperatures. CDs should be stored in their storage cases in an area of the vehicle that will not be subjected to damaging heat.

Region Number

Most DVDs are manufactured specifically for sale and use in a specific geographic region. The Region Number on a DVD must correspond to the Region Number of the DVD Player. The region number of the DVD Player is labeled on the top label on the top of the unit.

If the Region Number of a disc is different from the Region Number of the DVD Player, playback of the disc will not be possible.

NOTE: The PAV2000DTV is designed for use in Region 1 (North America).

Disc Insertion

CAUTION: With the screen in the open position, the driver may have difficulty seeing the disc insertion slot. As a safety precaution, discs should be inserted while the screen is in the closed position.

21

CONTROLS AND INDICATORS

Front Panel (With the Display Closed)

1.Volume Up/Down buttons

This button is used to increase/decrease the Audio Volume.

2.Tilt button

Momentarily press and release this button to adjust the angle of the TFT LCD panel with 3 steps. When this button is pressed and held for 2 seconds, the TFT LCD panel moves 2 steps backward & 1 step to forward.

3.Open button

This button is used to Open and Close the TFT LCD panel.

4.Reset button

This button is used to return the unit to the original factory settings (Initial Mode) if the unit fails to operate properly.

NOTE: If the unit still fails to operate properly after the Reset button has been pressed, contact your local Audiovox dealer for assistance.

5.Joystick

The joystick is used to choose all directional functions (UP/DOWN/LEFT/RIGHT). Once a selection has been made using the joystick, press Enter to confirm the selection.

6.Remote IR Sensor

The Remote IR Sensor is used to receive infrared signals from the remote control.

7.Power/Mode

The Power/Mode button is used to turn the unit ON and OFF. To turn the unit OFF, press and hold the button for 2 seconds. The Power/Mode button can also be used to switch between AV1, AV2, DVD, Radio and TV modes.

22

8.Menu/Setup

???Menu: This button is used to display the System Menu.

???Setup: Press and hold this button for 2 seconds to display the DVD MPEG Setup Menu.

???NOTE: This button is used to switch between receiving bands for Radio or TV modes.

9.Mute

This button is used mute all Audio outputs. Pressing the Mute button again will restore all Audio outputs.

10.P.S/BSM

This button is used to scan and store AM/FM stations. Momentarily press and release this button to start the scan mode. When a desired station is reached, press the button again to stop the scan mode. Press and hold this button for 2 seconds to store the station.

11.TRACK/TV CH Up/Down

This button is used to tune the stations to be stored in Radio and TV mode.

???Delete (I<<)

The Delete button is used to remove previously stored stations that are displayed on the screen. Press and hold this button until the selected station is deleted.

???Memory (>>I)

The Memory button is used to store desired stations. Once a desired station is displayed on the screen, press and hold the button until the station is stored into memory.

These buttons are also used to select the next Track or Song of an Audio or MP3 CD. These buttons are also used to select the next Chapter of a DVD.

12.Seek Tuning UP/DOWN

???In Radio Mode: This button is used to seek the next Radio station with clear reception.

???In TV Mode: This button is used to seek the next TV Channel with clear reception.

???In CD or DVD Modes: Press the directional buttons to scan Fast Forward or Fast Reverse on the disc. Press and hold the button for 2 seconds play the disc in Slow Forward or Slow Reverse.

13.Eject

This button is used to eject the disc from the unit.

14.Sub Level

Use this knob to adjust the Subwoofer level for analog line output only.

23

Rear Panel

1.RGB Input for Audiovox Navigation Connection

2.Minet for RT Box Connection

3.Optical Digital Output for Special Dolby Digital & DTS Decoder Connection

4.Mounting Bolt

5.Cooling Fan

6.16 Pin Power Connector

7.Video In/Out for RT Box Connection

24

Remote Control Functions

The remote control should be pointed directly at the IR remote sensor (as shown above) in order for the headunit to function correctly.

Distance: The maximum distance that the remote control can be used is approximately 16 feet from the front of the remote sensor.

Angle: The maximum angle that the remote control can be used is approximately ??30 degrees from center of the IR remote sensor.

NOTE:

???Do not install the headunit where direct sunlight or fluorescent illumination can shine directly into the IR remote sensor. Direct sunlight or fluorescent illumination could interfere with proper remote control operation.

???Avoid dropping the remote control.

???Avoid spilling liquids on the remote control or exposing it to extreme heat.

26

Remote Control Key Functions

27

28

SYSTEM OPERATION

Turning The System Power ON/OFF

To turn the system power ON, press and release the POWER button. The monitor will be vertically positioned when pressing Open/Close button.

Pressing and releasing the Open/Close button can also turn ON the system power.

To turn the system power OFF, press and hold the POWER button again for 2 seconds. The monitor will automatically close when the unit is powered OFF.

Opening The Monitor

Press the OPEN/CLOSE button to open the monitor.

Closing The Monitor

1.Hold the upper left & right side of the monitor parallel with the front of the unit as shown in the picture below.

2.Press the OPEN/CLOSE button or POWER button for 2 seconds or longer and the monitor will automatically close.

NOTE:

???If the monitor is not parallel to the front of the unit (the monitor is angled to the left or the right) the monitor cannot be closed. A beep tone will alert the user to the problem.

???If the OPEN/CLOSE button is pressed while radio or video is on, the monitor will close, and sound will still be audible. When pressing power button for 2 seconds, the sound and power will be ???OFF???.

29

Picture Control

1.Press the SYSTEM MENU button on the remote control until the monitor displays following picture and choose ???PICTURE??? on OSD.

the figure below.

30

5.Press the ENTER key for 2 seconds to return to the previous menu. When there are no keys are pressed after 5 seconds or if the SYSTEM MENU button is pressed, the OSD menu will disappear.

Audio Control

1.Press the SYSTEM MENU button on the remote control until the monitor displays the figure shown below.

31

6.Press the SYSTEM MENU button for about 2 seconds in order to return to the previous menu.

NOTE: When there are no keys are pressed after 5 seconds or if the SYSTEM MENU button is pressed, the OSD menu will disappear.

7.The Bass/Mid/Treble features can be adjusted from ???6 level to +6 level.

8.Repeat the same process for the other features that need to be adjusted.

9.Press the ENTER key for 2 seconds in order to return to the previous menu. Press the SYSTEM MENU button to leave the MENU OSD.

Initial Setting - (Color System)

1.Press SYSTEM MENU button until the monitor displays the following picture shown in the picture below.

32

ENTER key. The figure shown below will appear on the display.

4.With the cursor placed on the Color System feature, press the ENTER key to switch between NTSC and PAL modes. When there are no keys are pressed after 5 seconds or if the SYSTEM MENU button is pressed, the OSD menu will disappear. When no key is pressed for 5 seconds, the SYSTEM MENU will disappear.

5.Press the ENTER key for 2 seconds to return to the previous menu.

6.Repeat the above previous steps to adjust the Navigation, Auto Dimmer and Beep Tone features

Initial Setting - (Adjust TV System)

1. Press the SYSTEM MENU button and select the Initial Setting feature.

as shown in the figure below.

33

Initial Setting - (Adjust Sound Mix)

1. Press the SYSTEM MENU button and select the Initial Setting feature.

the ENTER key as shown in the figure below.

4.Each time ENTER key is pressed, the Navigation feature will change as detailed below:

???OFF ?? R ?? L ?? L+R

5.Press the ENTER key for 2 seconds to return to the previous screen.

6. Use the keys and place the cursor (Yellow Bar) on Handsfree and press the ENTER key as shown in the figure below.

36

7.Each time the ENTER key is pressed, the Handsfree feature will change as detailed below:

???OFF?? R ?? L ?? L+R

8.Press the ENTER key for 2 seconds to return to the previous screen.

9.Press the ENTER key for 2 seconds to return to the previous screen. Press the ENTER key for 2 seconds to turn the MENU off. Press the SYSTEM MENU button again to turn MENU OFF directly.

When there are no keys are pressed after 5 seconds or if the SYSTEM MENU button is pressed, the OSD menu will disappear.

Initial Setting - (Rear Camera)

1. Press the SYSTEM MENU button and select the Initial Setting feature.

4. Each time the ENTER key is pressed the USE feature will change as detailed below.

???ON ?? OFF

When there are no keys are pressed after 5 seconds or if the SYSTEM MENU button is pressed, the OSD menu will disappear.

5. Press the ENTER key for 2 seconds to return to the previous screen.

37

ENTER key as shown in the figure below.

7.Each time the ENTER key is pressed the ANGLE feature will change as detailed below:

???0 deg ?? 180 deg

8.Press the ENTER key for 2 seconds to return to the previous screen. Press the ENTER key for 2 seconds again to turn the MENU off. Press the SYSTEM MENU button again to turn the MENU off directly.

Rear Monitor

1.Press the SYSTEM MENU button and select Rear Monitor as shown in the figure below.

2. Use the keys for setting the Rear Monitor feature to DVD, Radio, TV, AV1, AV2, OFF as shown in the figure below. The Rear Monitor feature can be set via the Rear Monitor button on the remote control button.

When there are no keys are pressed after 5 seconds or if the SYSTEM MENU

38

button is pressed, the OSD menu will disappear. When no key is pressed for 5seconds, the menu will be disappeared. Or press SYSTEM MENU button again to turn MENU off directly.

OVERVIEW OF THE RDS FUNCTION

AF (Alternative Frequencies) / REG (Regional):

After turning the RDS feature on, AF can be set to become ???ON??? or ???OFF??? using the AF button on the remote control.

???AF ???OFF???: When the AF switching mode is set to OFF and RDS is set to ???ON???, a maximum number of 6 RDS and non-RDS will be stored together.

???AF ???ON???: When the AF switching mode is set to ON the RDS station information will only be displayed.

???AF Segment Flashing: When the AF switching mode is selected and the RDS information is not received yet AF segment flashing will occur.

When the AF switching mode is ???ON???, the radio continually checks the AF signal strength. The interval of checking time of each AF depends on the signal strength of current station which can be anywhere from a few seconds for strong station to a few minutes for weak station.

Every time a new AF is stronger than a current station, the AF will it switch over to the stronger station quickly.

To access the Region feature, press the PTY button on the remote control for 2 seconds and the REGIONAL mode will be set to ON or OFF.

-REG mode ???ON???: When the Region mode is set to ON the AF switching or PI SEEK is implemented to the station that has all PI codes that are the same as the current station. ???REG ON??? should be shown on screen.

-REG mode ???OFF???: When the Region mode is set to OFF the regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented. ???REG OFF??? should be shown on screen.

When the regional mode is ???OFF???, the radio may switch from a national program station to a local variant of that program, or from a local station in an area to a local station in another area. This may cause customers to listen to a wrong program. To avoid this feature set the Region mode to ???ON???, and then the radio will only switch to an AF that broadcasts Region mode to the same program.

39

TA(Traffic Announcement) / TP (Traffic Program)

TP mode will automatically switch between ???ON??? and ???OFF??? depending upon the broadcast. In order to access the TA mode, press the AF button on the remote control for 2 seconds and the TA mode will switch between ???ON??? and ???OFF???.

When the TA mode is ???ON??? and a traffic announcement is received the following may occur:

???The unit will switch out of DVD/TV/AV1/AV2 modes temporarily to radio mode.

???The volume level will be raised to the threshold point. If the volume level was greater than the threshold point, the volume will decrease.

???When the TA mode is ???ON???, the OSD will display ???TA ON???

???When a TP station is received, the OSD will display ???TP ON???.

PTY (Program Type)

To access the Program Type feature, press the PTY button the remote control and the OSD will display ???PTY ON??? or ???PTY OFF???. When in the ???PTY ON??? mode, the different program types can be selected by using the track up and down buttons (I<<, >>I)

RDS (Radio Data System)

When the RDS function is set to ON the OSD will be similar to that as shown in the figure below.

4. Press P.S/BSM button to store the RDS stations.

NOTE: Only six RDS stations can be stored at one time per band.

40

DVD Player Operation

Changing DVD System Setting

Press the MPEG SET UP button on the remote control, and five categories will be displayed on the screen: Language, Video, Audio, More Audio, and Parental. Use the directional arrows and to select between the displayed features. Use the ENTER button to select the desired feature.

Language

Within the Language menu, the following features can be adjusted: OSD Menu, Subtitle, Audio, and DVD Menu. Use the directional arrows and to choose the desired selection. Use the directional arrows and to adjust the settings. The available language settings are English, French, Japanese, Korean, and Spanish.

Video

Within the Video menu, the following features can be adjusted: TV Shape and TV System. Use the directional arrows and to choose the desired selection. Use the directional arrows

and to adjust the settings. TV Shape can be adjusted to the following features: 16:9, 4:3 PS, and 4:3 LB. TV System can be adjusted to the following features: NTSC, PAL, and AUTO.

42

Audio

Within the Audio menu, the following features can be adjusted: Dolby Digital, DTS, MP3/WMA, and CD/VCD. Use the directional arrows and to choose the desired selection. Use the directional arrows and to between digital and analog out. Use the ENTER button to adjust the settings. The Analog output can be set for 2-Channel and 6-Channel Output. The digital output can be set for PCM, RAW, or OFF.

More Audio Settings

Within the More Audio Menu, the following features can be adjusted: Speaker Setting, Speaker Level, Speaker Delay, Dynamic Range Compression Decompression, Prologic and Pink Noise. Use the directional arrows and to choose the desired selection. Use the directional arrows

and to adjust the settings.

Speaker Setting

Press the ENTER button to cycle the Speaker Setting between two modes: Center and Subwoofer. To select a feature, press the direction button and "Yes" and "No" will appear on the screen. Use the directional arrows and to select either yes or no.

???"Yes": The audio output of the Center and Subwoofer speakers will be separated. Based on the 5.1 CH decoder. A separate Center or Subwoofer speaker is necessary.

???"No": The audio output of the Center and Subwoofer speaker will be sent to Front Rear speakers. This feature should be used when the system does not have a separate Center or Subwoofer speaker.

43

Speaker Level

Press the ENTER button to cycle through the Speaker Level selections for 5.1 CH speakers as follows: Center, Left Surr, Right Surr, Subwoofer, Front Left, and Front Right. Each time the ENTER button is pressed, each mode will change. To select a mode, press the direction arrow and the display will show the level at 0 dB. The level can be adjusted by using the direction arrows and . Press the ENTER button to choose the level selection.

Speaker Delay

Press the ENTER button to cycle through the Speaker Delay selections for delay time as follows: Center Delay and Surr Delay. Each time the ENTER button is pressed, each mode will change. To select a mode, press the direction arrow and the display will show the delay starting at 0 ms. The delay time can be adjusted by using the direction arrows and

. Press the ENTER button to choose the delay time.

Dyn Range Comp (Dynamic Range Compression)

Press the ENTER button to cycle through the Dynamic Range Compression modes as follows: Full or Off.

???Full: In order to limit the audio output, select this mode and the volume level will be decreased by a specified level.

???Off: In this setting, the Dynamic Range Compression mode is "Off".

Prologic

Press the ENTER button to select the Prologic settings. Prologic can be set to Auto, ON, or OFF. Use the directional arrows and to cycle through the selections and press the ENTER button.

???Prologic On: In this setting, when the original audio output is 2CH, Stereo, this mode will render the audio output as virtual 5.1CH sound. This mode only applies to DVD and CD Audio modes.

???Prologic Off: In this setting, the Prologic mode is "Off".

. Pink Noise can be set to the following modes: Off, Left, Center, Right, Left Surr, Right Surr, and Subwoofer. This mode confirms the proper location for each speaker and the pink noise is audible in each speaker, and the correct location can be verified before the final setting.

44

Parental

The Parental Menu prohibits the play of specified DVDs that are unsuitable for children. Press the ENTER button to access the Parental Menu. There are two features within the parental menu: Password and Rating.

The Password feature is initially unlocked. To set a password, enter a 4-digit code and press the ENTER button.

The Rating feature allows the user to set the Parental rating level of the allowable discs to be played. The rating levels are as follows:

1.Kid safe

2.G

3.PG

4.PG-13

5.PG-R

6.R

7.NC-17

8.Adult

Use the ENTER button to cycle through the rating level selections.

45

Disc Playback Operation

Disc Insertion

Insert a disc into the center of the insertion slot with the label side facing up. The disc will automatically play after loading.

NOTE: Do not insert foreign objects into the disc insertion slot. If the mechanism does not accept the disc, either there already may be a disc in the unit or the unit may need service.

Loading 8 CM disc into the center of the insertion slot

Power/ Mode

The Power/Mode button turns the system ON and OFF. To turn OFF the unit, press and hold the Power/Mode button for 2 seconds. Each time the Power Mode button is pressed, the source will change from DVD / RADIO / TV / AV1 / AV2. When there is no disc in the loader, the mode will automatically switch to Radio mode. The last mode will be memorized when the system is powered off.

Open/Close

The OPEN button on the unit and the remote control will either open or close the monitor screen. The monitor will only open when the OPEN button is pressed although the unit power is on. The monitor will automatically close when the system is powered off.

Eject

In order to eject a disc, press and hold the EJECT button on the unit for 2 seconds. Pressing and holding the STOP button on the remote control for 2 seconds will also eject the disc.

Play/Pause

The disc will load and playback will begin automatically. Upon insertion, when the Play /Pause button is pressed a second time the disc play will be paused.

???If a single-sided disc is loaded upside down, the disc will automatically eject after a few seconds.

46

???If an Audio CD is inserted, the monitor will display "CD" on the screen.

When all chapters on the disc have been played, the unit will automatically stop playing.

Using the Remote Control

To select a function that is printed on a button on the remote control, press the desired button for 1 second. To select a function that is printed above a button on the remote control, press and hold the desired button for 2 seconds.

Changing Subtitle Language (S-TITLE)

To change the subtitle language to a different language from the language selected at the initial setting, follow the steps detailed below:

???Press the S-TITLE button (the number 5 button on the remote control) for 2 seconds during playback.

???Repeatedly press the S-TITLE button until the desired language is selected.

???To turn OFF the subtitle feature, press the S-TITLE button until "OFF" is displayed on the screen.

Note: This feature only works with discs with multiple subtitle languages.

Changing the Audio Soundtrack & Language (AUDIO)

To change the Audio Soundtrack Language to a different language from the language selected at the initial setting, follow the steps detailed below:

???Press the AUDIO button (the number 6 button on the remote control) for 2 seconds during playback.

???Repeatedly press the AUDIO button until the desired Audio Soundtrack Language is selected.

NOTE: This feature only works with discs with multiple audio tracks.

47

Direction Buttons-Menu/Title Navigation and Movement

Press the direction buttons ( , , , ) to navigate through various on-screen selections. Press the ENTER button to select a desired feature.

After Playback

When the unit is not in use, eject the disc and turn OFF the power by pressing the POWER button for 2 seconds.

NOTES:

???If the icon ??? ??? appears on the screen when a button is pressed, this indicates that the selected function is not available on the disc at that time.

???Depending on the DVD disc, some operations or features may not be allowed. Refer to the jacket or case of the disc for further information.

Last Memory Feature

The unit is equipped with a "LAST MEMORY" function that allows the user to resume viewing of a movie from the point where it was last left off.

NOTE: The Last Memory function is not supported once the disc is ejected.

Volume UP and DOWN

The volume of the audio output can be adjusted by pressing the Volume and buttons.

GOTO Search Feature

The GOTO Search feature allows the user to move to any title, chapter, or elapsed time on the disc. Press the GOTO button (the number 9 button on the remote control) for 2 seconds and the search features are selectable on the screen as detailed below:

???Time: Input the desired elapsed time with the Numeric Keypad, and press the ENTER button.

???TITLE/CHAPTER: Input the desired title or chapter number with the Numeric Keypad and press the ENTER button.

49

MP3 Disc

Track Up & Down ( I<<, >>I)

Use the Track Up and Down buttons or the directional buttons ( and ) to skip to the next or previous song. To see the next page on the screen, use the directional buttons

( and ).

Numerical Key Pad

MP3 files can be selected via the numerical keypad.

Photo CD

Press the Title Menu button, while accessing the Photo CD to display and preview the first 9 pictures on the disc. Use the directional buttons ( , , , ) to navigate through the pictures. Press the ENTER button to select a picture to display on the screen.

51

AM/FM Radio Operation

Band (AM/FM)

Repeatedly press the BAND button on the remote control to change between the FM and AM bands as follows:

??? FM1 / FM2 / FM3 / AM1 / AM2 Each band can store 30 stations.

OSD ON/OFF

???When the changer is connected, the OSD for changer information will be shown in AV2 mode. Press the BAND button, and the OSD of the changer information will be "ON" or "OFF".

Seek (Manual) UP/DOWN

The Seek Up/Down feature allows the user to manually tune to a radio station. Press and hold the SEEK button for 2 seconds to access the Seek Mode. To use this button for Manual Tuning, press this button for 2 seconds and then tune the frequency by channel spacing. If a button is not pressed for 5 seconds, the mode will change back to SEEK mode.

???Memory: In order to memorize the station as tuned manually, first press the SEEK UP/DOWN buttons and press and hold this button after finding the station. Then, the desired station should be memorized.

Preset Radio Station SCAN

(P.S/BSM button on the display or P.SCAN button on the remote control.)

With the Preset Scan feature, the unit will scan the desired band for tunable stations. First, select the desired band (FM1/FM2/FM3/AM1/AM2) and press the PS/BSM button for 2 seconds. The tuner will then search until a station of sufficient signal strength has been found. The unit will store 30 stations in the band automatically starting at the strongest signal strength.

Press this button quickly and stations will be automatically stored. When seeking for a desired station, press this button once, and the Tuner will stop at the station.

Stored Radio Station Deletion

Locate the radio station as shown on the monitor by using the direction buttons ( , , , ).

???Delete: First select a stored station to be deleted as shown on the display. Then press the DELETE button to erase it from stored memory.

52

TV Operation

Seek (Manual) UP/DOWN

The Seek Up/Down feature allows the user to manually tune to a TV channel. Press and hold the SEEK button for 2 seconds to access the Seek Mode. To use this button for Manual Tuning, press this button for 2 seconds and then tune the frequency by channel spacing. If a button is not pressed for 5 seconds, the mode will change back to SEEK mode.

???Memory: In order to memorize the TV channel as tuned manually, first press the SEEK UP/DOWN buttons and press and hold this button after finding the station. Then, the desired TV channel should be memorized.

Preset TV Channel Scan

(P.S/BSM button on the display or P.SCAN button on the remote control.)

This button is used to scan through preset TV channel. First select the desired TV band (TV1 or TV2) you would like to scan and then press and release either the P.S/BSM button or the P.SCAN to begin scanning within the selected TV Band for the desired TV Channel. The TV Tuner will search for stations of significant signal strength and store up to 30 of these stations automatically.

Stored TV Channel Deletion

Locate the TV Channels as shown on the monitor by using the direction buttons ( , , , ).

???Delete: First select a stored TV Channels to be deleted as shown on the display. Then press the DELETE button to erase it from stored memory.

Fine Tune

Press this button about 2 seconds or longer to tune the TV channel for a fine tuned picture.

53

TROUBLESHOOTING

54

55

12 MONTH LIMITED WARRANTY

Applies to Audiovox Video Products

AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below.

This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for installation, removal or reinstallation of the product, or to damage to tapes, discs, speakers, accessories, or electrical systems.

This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS

LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,

SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY

PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED

WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE

LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR

BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE

OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA

128-5495D

56