Installation

Instructions

Thank you for selecting American-Standard...the benchmark of ???ne quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

H

C

Certi???ed to comply with ANSI A112.18.1M ASSE 1016

M968662 REV . 1 . 1

CARE INSTRUCTIONS:

To keep your new faucet looking new, please follow these simple care instructions:

DO: Simply rinse the faucet clean with clear water. Dry the faucet with a soft cotton cloth.

DO NOT:

Do not use any abrasive cleaners, cloths, or paper towels.

Do not use any cleaning agents containing acids, polish abrasives, or harsh cleaners or soaps.

Regular and routine cleaning will reduce the need for heavy cleaning and polishing. If heavy cleaning is required, the following procedures are recommended:

Remove as much surface dirt and ???lm using clear water and soft cotton cloth (as described above).

Use any of the following to remove tough surface ???lm and build-up:

Mild liquid detergents

Clear ammonia free liquid glass cleaners Non-acidic, non-abrasive gentle liquid or fully dissolved powder cleansers mixed according to manufacturers directions.

Non-abrasive liquid polishers

Once clean, rinse faucet again with clear water to thoroughly remove cleaner or polish and blot dry with a soft cotton cloth.

Failure to follow these care instructions may damage the Faucet's ???nish.

1 TRIM INSTALLATION

Push CAP (1) over the O-RING SEAL (2).

Push DIAL PLATE (6) over CAP (1) and into the four alignment holes in ESCUTCHEON (3).

1

3

4

ALIGNMENT

HOLES

5

6

H

C

2 HANDLE INSTALLATION

Install STEM ADAPTER (1) onto KNOB MOUNT (2) with ADAPTER SCREW (3).

Align HANDLE (4, 4a) and push onto KNOB MOUNT (2).

Tighten SET SCREW with HEX WRENCH (5) supplied.

4a

2

5

3 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION

Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows:

Shut off water supply.

Remove handle and rim

Remove check stops and re-install them transposed.

Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left.

Turn the water supply back on and perform the temperature adjustment in step 4.

CHECK STOP

(RED TO BLUE)

CHECK STOP

(BLUE TO RED)

4 TEMPERATURE CALIBRATION

Check that arrow marking B points vertically upwards. If not, push the BLACK CLAMP (1) on the SECURING RING (2) to the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" pointing upwards.

For 100??F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100??F. Check that arrow marking A on the KNOB MOUNT (3) still points upward after adjusting the thermostat to 100??F. If not, pull out the RED LOCKING DEVICE (5). Remove KNOB MOUNT (3) without turning by sliding out as indicated by the arrow.

Reinstall the KNOB MOUNT (3) so that the arrow marking A points upwards. Reinstall RED LOCKING DEVICE (5).

2

5

5 OPERATING THE VALVE

Turn on water supply on and test installed ???tting.

If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed. See step 3 for TRANSPOSED SUPPLY PIPING.

Operate valve from off to cold to hot. Check temperature. If max mixed water temperature is to hot or to cold see step 4 and re-calibrate the valve.

H

C

HOT

COLD

OFF

A907090-YYY0A

CAP

A918434-0070A

ESCUTCHEON SCREWS

H

C

M918038-0070A

ADAPTER

M918990-0070A

SELF TAPPING SCREW

M950118-YYY420A

LEVER HANDLE

M950119-YYY420A

CROSS HANDLE

Replace the "YYY" with appropriate ???nish code

HOT LINE FOR HELP

For toll-free information and answers to your questions, call: 1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-12-00

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . ?? A S A m e r i c a , I n c . 2 0 0 8

M968662 REV . 1 . 1