INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Champion?? 4 2-piece Toilets

Models - 2002, 2018, 2023, 2414, 2585, 2792, 2586, 2793, 3186, 3404

Doral Classic??? Champion?? 4 2-piece Toilets Models - 2058, 2074, 2076, 2473

Doral Classic??? Champion?? 4 2-piece Toilets

Models - 2367, 2368, 2369, 2443

Oakmont??? Champion?? 4 2-piece Toilets

Models - 2625, 2627, 2738

Townsend??? Champion?? 4 2-piece Toilets

Models - 2733, 2735

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

NOTE: BACK-TO-BACK INSTALLATION

Depending upon your plumbing and venting conditions, the flow from the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water downward and away from the other toilet.

Recommended fitting type for back-to-back installations.

RECOMMENDED TOOLS AND MATERIALS

1REMOVE OLD TOILET

a.Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b.Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c.Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d.Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

S A V E F O R F U T U R E U S E

2 NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY. THEY ARE NOT EXACT REPRESENTATIONS.

5 MANIFOLD INSIDE WATERWAY ??? DO NOT REMOVE

NUT

TAPERED

WASHER

CLOSET

BOLT

FLANGE

POSITION TOILET ON FLANGE

a.Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.

b.Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!

7

MTG.

RIBS

WASHER/NUT

INSTALL TANK

Recommended tool: Deep socket tool included in tank kit.

a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nuts. Use the included deep socket tool to help get nuts started on bolts.

b.With tank parallel to wall, alternately tighten hex nuts keeping tank even and level until tank contacts both front and rear bowl mounting ribs. Do not tighten any further.

WASHER/NUT

DEEP SOCKET

TOOL

SCREWDRIVER

DEEP

SOCKET

TOOL SCREWDRIVER

!CAUTION: DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!

DO NOT SPIN BOLTS INSIDE TANK WITH A SCREWDRIVER

8INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.

CAUTION: DO NOT USE

CONE WASHER WITH

PLASTIC SUPPLY LINE.

CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding.

!WARNING: Do not use plumber???s putty, pipe dope, or any other sealant on the water supply connection to this tank. If the connection leaks after hand tightening, replace the supply line.

If the connection continues to leak with the new supply line, replace the fill valve.

Warranty is void if any type of sealant is used on the water supply connection.

1.Turn off water supply and flush toilet to empty tank.

2.Disconnect chain from trip lever by removing hair pin cotter

NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.

14

LIFT ARM

FIRST

Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc.

TROUBLESHOOTING

IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 14.

IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because:

???The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided.

???The flush valve is leaking because it's worn, dirty or misaligned.

IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed.

Go to our website at www.fluidmaster.com for more solutions to toilet problems.

For troubleshooting information please contact:

30800 Rancho Viejo Road

San Juan Capistrano, CA 92675

(949) 728-2000 (800) 631-2011

www.fluidmaster.com

?? 2001 Fluidmaster, Inc.

?? Registered trademark of Fluidmaster, Inc.

REPAIR PARTS LIST

Repair parts are determined by toilet tank number which can be found marked inside tank.

NOTE: "XXX" represents color or trim finish options. Specify when ordering.

??????

???

???

??? ??? ??? ???

In the United States:

American Standard Brands

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Customer Care For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 442-1902

www.americanstandard.com